The side length of I-beam is small and the height is large, so it can only bear the force in one direction.The side length of I-beam is small and the height is large, so it can only bear the force in one direction.Chikimura, . the straight length of the hook of the surface mesh reinforcement at the grid support shall not be less than mm, and the bending diameter shall not be less than D (D is the reinforcement diameter).It is widely used in various fields of national economic construction, such as buildings, bridges, power stations, oil drilling platforms, vehicles, highways, subways,ChikimuraWhat is the inner diameter of 8-inch welded pipe,All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.Alloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment, or pipeline, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects. Hot hole breaking cold rolling method. This method is dominated by expansion and expands vertical sliding and skew rolling. The former one is mainly cold rolling by relatively limited mandrel mill cold rolling by few station mandrel mill, cold rolling by three high limited mandrel mill and cold rolling by fluctuating mandrel mill. In this way, the advantages of high efficiency,ChikimuraHow much is a meter of welded pipe, low metal material consumption, multi specifications and high precision. Therefore, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning,Chikimura38CrMoAl alloy pipe, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.Seamless pipe has a high position in steel pipe, and there are many large factors. The main usage has accounted for more than %, which is applicable to all walks of life. Seamless pipe factories in China are widely produced. At present, the number of factories in China is also increasing every year which is determined by the nature and production conditions of seamless pipe. The common production processes and processes are more complex.Greatly reduce the environmental pollution caused by abrasion, and increase the labor cost of material cleaningDiscount damage and blanking,Function of I-beam: where is I-beam mainly used?Defects of alloy pipe and solutions:The import and export order of I-beam is generally based on the specifications required in use after determining the corresponding carbon structure steel (or low alloy steel) steel grade. Except for the specification number, I-beam has no specific composition and performance series.

After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.Management Department,Application characteristics of I-beam Spiral seam high-frequency welded steel pipe (sy- for general low-pressure fluid transportation takes hot-rolled steel strip coil as pipe blank and is often spiral formed at warm temperature. High frequency lap welding method is selected for welding spiral seam high-frequency welded steel pipe for general low-pressure fluid transportation.I-beam, whether ordinary or light, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures.Chikimura,X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.