C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.If the test results of square tubes fail to meet the provisions of product standards the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Joyabay,Cutting: to be fast, no teeth, or whether the cutting line is flat, the starch taste of oil affects the quality of dishes. First choose to cut potatoes with less sharp bottom, so when you cut,JoyabayGalvanized steel pipe hot dip galvanized steel pipe, it's easy to leave the corner of the side end.Generally, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, which can remove oxide scale, rust and old coatings. Professional square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the environment.LozovaGenerally speaking, square pipe welding has a process: ignition, pressurization and thermal insulation.The square tube for fluid transportation (gbt-) is a general square tube for transporting water, oil, gas and other fluids.Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.

The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.Square tubes are low alloySquare pipe is the name of square pipe, that is,Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, pipes and metal products. In order to facilitate the production, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, medium section steel, small section steel and square tube cold bending Section steel, wire rod, medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, square pipe, welded steel pipe, metal products, etc.Solution treatment and nondestructive testing sand rolling treatment and sand blasting treatment many manufacturers in the market do not do solution treatment and % penetration nondestructive testing, and many of them use sand blasting instead of sand rolling. After these steps are omitted, the cost is greatly reduced.With the improvement of production quality, the quality of square tubes is getting better and better. The quality of square tubes will affect our lives. Because the functions of square tubes are different, their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.

The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, compared with straight seam pipe of the same length, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes on-site settlement, honest operation, local offices, long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.Finance Department,Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.Square tube failure. When the pipeline is erected, it is necessary to do a good job or directly use the square pipe. The reason for the corrosion of the pipeline is that the layer of the pipeline is damaged. Once the layer is separated from the pipe surface, it will naturally cause failure.When sand blasting or manual mechanical derusting is used, due to the falling off of the oxide scale of the galvanized square pipe, the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, the surface of the galvanized square pipe is easy to rust again, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes and other materials all year round. I operate in good faith. Welcome to call! As the paint is a time-effective material the overstock of inventory is easy to expire. Therefore, the main indexes of the paint must be rechecked before use, and the paint can be used only when the results meet the standards.Joyabay, the carbon content generally does not exceed %. In addition to iron and carbon, the main elements of steel also include silicon, sulfur, phosphorus, etc. There are various classifications of steel and square tubes, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%, S & le; .%)The other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection,JoyabayHot dip galvanized steel grating plate, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.