Dehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlementHowever, what we need to do now is to improve the production technology level of China&#;s production process of C-section steel, it is more conducive for C-section steel manufacturers to produce C-section steel products suitable for truck industry.Guaran, Spiral seam high-frequency welded steel pipe (sy- for general low-pressure fluid transportation takes hot-rolled steel strip coil as pipe blank and is often spiral formed at warm temperature. High frequency lap welding method is selected for welding spiral seam high-frequency welded steel pipe for general low-pressure fluid transportation.Plan option : Martensitic chromium alloy pipe,Due to the unique performance of I-beam, I-beam has successfully solved the problem of serious equipment wear in many industries.I-beam is a long strip steel with groove section, which belongs to carbon structural steel for construction and machinery. It is a section steel with complex section, and its section shape is groove shape. China&#;s imports of I-beams are greater than its exports. The main producing areas are Tangshan Iron and steel, Baotou Iron and steel, Shangang, huangte, Maanshan Iron and steel, Xuanhua Iron and steel, Japan iron and steel, etc.After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.

The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected. The end span plate is connected with the load-bearing wall. The length of the surface mesh extending into the grid support shall not be less than mm, and a transverse reinforcement shall be provided at the end of the mesh or the extended reinforcement shall be bent.In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, aluminum the heat treatment of steel is the main content of metal heat treatment. In addition, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.Inspection environment,The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Last week, the billet in North China market showed a slight rebound trend. The billet quotation in Tangshan, the leading city, rose first and then stabilized in four trading days with a strong wait-and-see atmosphere in the market. Affected by the almost stagnation of festival procurement, Tangshan billet fell by yuan during the Dragon Boat Festival holiday. On the first day after the festival, although the phase snail is still running at a low level, due to the small billet resources in the market, the steel mills unexpectedly rose, and the billet market rebounded. However, due to the continuous increase of capital pressure and the downturn in the transaction of downstream finished materials, the steel plant has always maintained a cautious wait-and-see attitude to maintain stability. Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason,GuaranWholesale of welded pipe, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc.

H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, and can save a lot of materials and construction time.investment,Guaran20# hot dip galvanized seamless pipe,GuaranHow much is a quarter galvanized pipe of six meters,Greatly reduce the environmental pollution caused by abrasion, damage and blanking, and increase the labor cost of material cleaningGalvanized pipe refers to the shape and high frequency of hollow square steel pipe welded by the back of the steel pipe during the hot rolling or cold rolling of galvanized steel plate or cold bending of galvanized steel plate, or before the galvanization of cold hollow pipe. Galvanized. Galvanized square pipe can be divided into hot galvanized pipe and cold galvanized pipe from the production process. This is because the two galvanized pipes are different, which also leads to many different physical and chemical properties.The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good.Guaran,I-beam is widely usedMetallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, siliconizing and so on are commonly used in production.Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.