Potential is convenient and flexible. It is easy to operate. It can be operated by a fool who turns on the power supply under immersion; It has a wide range of applications. In many cases, it belongs to a portable workstation which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　 important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.Encrucijada,　　It is necessary to set up a protection system,EncrucijadaVertical non clogging sewage pump, which can protect the operation of the electric pump. But this is not the key to the problem. The protection system is just a remedy after the pump fails. It is a passive method.　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in waterhamburg , we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, when

　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices,EncrucijadaSewage pump diving, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　First of all, the slurry pump is divided into three categories from the installation method: horizontal slurry pump, vertical slurry pump, submersible slurry pump horizontal slurry pump: also known as dry installation slurry pump, because it is installed on the ground and the surface of the pump body cannot contact the slurry, it is called dry installation. When this type of pump is installed,　　Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.Honesty is the foundation,　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.

　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload,　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.　　The sewage pump will leak. If the water pipe leaks, it will reduce the power of the water pump and even damage the sewage pump. In case of fixed installation, it shall be applied on the pipe to avoid leakage. Pages can be welded by electric welding, buried in the soil, coated with asphalt, and then should not be gassed. Steaming of tap water products　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pumpEncrucijada,　　Rate loss, so shaft power = effective power + lost power.　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is full　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.