The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.The second is the pickling of the square pipe. Both chemical and electrolytic methods are used when pickling the square pipe. These two methods can remove the oxide skin of the square pipe.Tapachura,The covering shall be strong and durable to prevent decay and leakage caused by long-term sun and rain.We all know very well. Therefore, the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.Epworth, square rectangular tube, seamless square tube, galvanized square tube galvanized tube, old brand, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission, with standard number of gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.

Generally, which can remove oxide scale rust and old coatings. Professional square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the environment.Upper yield point (& sigma; Su): the large stress before the yield of the sample occurs and the stress decreases for the first time; Lower yield point (& sigma; SL): the small stress in the yield stage when the initial instantaneous effect is not considered.The difference between square pipe and seamless steel pipe the main feature of seamless steel pipe is no welding joint and can withstand large pressure. The product can be very rough as cast or cold drawn parts.plan,Cleaning solvent and emulsion can clean the surface of square tube to remove oil, grease, dust, agent and similar organic matter, but it can not remove rust, scale, welding, etc. on the surface of square tube, so it is only used as an auxiliary means in production.Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes,TapachuraWhat is the price of galvanized square tube, square tube is generally divided into sections, plates, pipes and metal products. In order to facilitate the production, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, medium section steel, small section steel and square tube cold bending Section steel, high-quality section steel, wire rod, medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, square pipe welded steel pipe, metal products, etc.B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.

Change to square pipe: generally, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )Workshop cost,Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.In the standard of qb square tube, most of them specify tensile test and hardness test at the same time. For those materials that are not convenient for hardness test, such as qb square tube,Tapachura125 galvanized square pipe, only tensile test is specified. In particular, the new portable surface Rockwell hardness tester and pipe Rockwell hardness tester can quickly and accurately test the hardness of stainless steel plate, stainless steel strip and qb square tube as thin as .mm,High quality steel (P & le; .%, S & le; .%)The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.