Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasion　　Let the medium containing some solid particles generate a certain flow rate so that the equipment can drive the solid to flow when it is in use,Abu DhakaHH slurry pump, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simpleAbu Dhaka,　　Submersible pump: as the name suggests, the whole pump (with motor) needs to be in the slurry.　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment willNea Ionia,　　In order to ensure the demand for water and electricity for production and living, many units hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this, it and the generator naturally become popular　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, and the site is cleaner.　　 repair and level the welding part of the submersible slurry pump with a file,Abu DhakaSplit vertical pipeline pump, clean the part to be bound with alcohol again and wipe it dry.

　　In the mud pump the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　　I believe you have such a question when using the submersible sewage pump, that is, is this pump a submersible pump? Or is it a sewage pump? In fact, this question is very easy to distinguish. You can take a look at the following contents sorted out by Shanghai Shenquan.　　There are differences.assets,　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, so as to avoid people　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore,Abu DhakaDrilling fluid slurry pump, many pumps tend to have better measurement results when in use.　　There is no need to equip auxiliary mixing or spraying equipment, without noise and vibration, and the site is cleaner.

　　In this way, a smooth surface can be formed on the surface.Inspection standard,　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.　　 Assembly of electric pump: assembly sequence of motor: stator assembly → lower guide bearing assembly → rotor assembly → thrust disc → left nut → thrust bearing assembly → base assembly → upper guide bearing seat assembly → skeleton oil seal → connecting seat. Adjust the studs so that the motor shaft extension meets the specified　　 First remove the pump from the engine.Abu Dhaka,　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone