KomayaguaHow much is cold drawn welded pipeSpecification model
2023-03-28 16:49:49The section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.The storage of galvanized pipes should pay attention to several points. The first is the storage location. It cannot be placed in the open air, because in the open air, not only the safety of various products such as theft, but also corrosion problems will occur. Open air sites are vulnerable to various extreme weather conditions. Large amounts of rain or snow will erode the zinc coating on the surface to the greatest extent, which may lead to rust of the product. The second is the details of storage. It is not directly exposed to the sun. It shall be cooled and dried and shall not be stored with corrosive articles.After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.management,The utility model has the advantages that the axial force of the roll is small, the axial movement is small, and the working slope is not requiredI-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.The section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.
I-beam is mainly divided into ordinary I-beam, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.Installation material list,Stages needing attention in the production and manufacture of alloy tubesRecently, the price of zinc has been falling continuously. The key reason lies in the soft skin of galvanized pipe consumption and the slow start of production and marketing rate of manufacturing industries in the middle and lower reaches after the Spring Festival. The disadvantage of zinc price has long been far beyond the level of cyclical factors. The main performance of no prosperity in the hot season is whether the market situation in the off peak season will become a more worried problem in the galvanized pipe sales market.Alloy pipe can be divided into round steel pipe and special-shaped steel according to different cross-sectional area. Because the circular area is large on the premise of the same side length, a large amount of liquid can be transported with an annular tube. In addition, when the circular cross section bears the internal or external axial working pressure,KomayaguaSC embedded threading welded pipe, the bearing force is more symmetrical. Therefore, most seamless steel pipes are round steel pipes.KomayaguaAlloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.Ways to obtain surface compressive stress characteristics of alloy tubes Frame line crack