Laminate flooring contains a certain amount of indoor formaldehyde, which is harmful to the body beyond the index required by the state (mg / L).When purchasing, it is best to select commodities with national environmental protection logo verification or national inspection free products. SmellSfantu-Gheorghe,The standard laminate floor surface should contain aluminum oxide wear-resistant paper. It has g, g, g, and even lower. It is directly sprayed with aluminum oxide on the decorative paper. The state stipulates that the surface wear-resistant revolution of the laminate floor for indoor use should be more than revolutions. Only the floor with g wear-resistant paper can meet the requirements. The wear-resistant revolution of g wear-resistant paperThe number of revolutions can reach -, or even lower than g. It is good if the number of revolutions directly sprayed with aluminum oxide can reach -. For those with low wear-resistant revolutions, the material cost is relatively low; because of its low wear-resistant degree, the tool cost during processing is also low. On the contrary, the cost is much higher if the number of wear-resistant revolutions is high. Easy to clean: medical treatment is simple, bright as a new mouth, no stains, easy to clean.The surface paint of solid wood composite floor is very good, with good wear resistance, without excessive vitality maintenance.According to statistics, the solid wood composite floor prepared for the sales market will not be waxed within years, and the wind color of automobile coating will also be maintained.This is obviously compared with the maintenance of solid wood flooring.The combination of hardness and softness.The wood floor in the living room should be made of boards without knots, cracks and mildew. Generally, Fraxinus mandshurica, camphor and teak are better, because their lines are beautiful and clear, and their texture is moderate.The laying method of wooden floor is not very difficult, but it is required to have a certain carpentry foundation.Firstly, and the floor shall be cleaned before laying.When laying, and lay from the center to the four sides. glue and an appropriate amount of cement can be used for bonding between laths.Note that the glue must be coated evenly to avoid the warping of the plate.

Call a deer a horse: the commercial family pretends that the low-priced tree species are high-priced tree species, which is purely to deceive consumers by using the blind spot of consumers&#; knowledge. The construction of installation works is convenient.Headache, dizziness, fatigue, nausea, vomiting, nausea, chest tightness, shortness of breath eye pain, sore throat, stomach pain, palpitation, shortness of breath, insomnia, weight loss, memory loss, autonomic nerve obstruction, etc.Long term inhalation by pregnant mothers is likely to cause abnormal fetuses and even death.recommend, Stimulating effect.Finally, heat conduction is fast. Rich colors and patterns

The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth,ChinautlaWhat color do wooden floors have, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap cut with a cutter along the ruler,ChinautlaLaminate flooring brand ranking, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, and then compact it.Finally use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground the service life of paint,Common types: three-layer solid wood composite floor, double-layer solid wood composite floor, new solid wood composite board.Moisture content is one of the most important factors affecting the reliability of solid wood composite flooring. When purchasing solid wood composite flooring, consumers should know whether the moisture content of the floor meets the national industrial standards.Second, the time of birth.Chinautla,Look at the substrate, break the floor, and look at the substrate inside. There are no impurities in the good substrate, and the color is relatively pure. You can see a lot of impurities in the poor substrate with the naked eye.Most domestic floors use fast-growing forests, and wood has been used since - years. However, imported floors, especially FSC certified plates, have strict restrictions on wood types, so wood substrates are better. Advantages.Wooden wedges and nails shall not be used for fixing during construction.The contact surface between the wooden wedge and the nail is too small, and the grip strength of the nail is insufficient.Bones are easy to loosen, and people will make a sound when stepping on them. SPC floor surface will not have holes and water seepage;There will be no seams after splicing. After being stained wipe it gently with a rag to clean it easily, leaving no marks that are difficult to remove, and there is no need to maintain it with special maintenance products.