Promote the continuous expansion of the sales network group.　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for useRaleigh,　　There is no suction line. As the water storage tank is not deep enough and the suction pipe of the water pump is not deep enough,RaleighCarbon steel explosion-proof pipeline pump, the inlet pipe of the water vortex is not deep enough. Water with a lot of gas. Destroy all normal water Self-priming pumps. To ensure sufficient depth of digestion and absorption of low watermark water. At that time, the depth was .~lm, and it was impossible to　　If the oil seal ring of the shaft is seriously worn replace it with a new one.OElgiy,　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand,RaleighDrilling fluid slurry pump, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.

　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.　　No. is generally expressed in fractional form, and the flow passage parts of this kind of slurry pump can be made of two materials, one is wear-resistant metal material, the other is wear-resistant rubber material. According to the working conditions, senior engineers of Panshi pump industry can select and design for you; For example, ZJ series　　 the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.Administration,　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.

　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious,RaleighCirculating hot water pipeline pump, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, whenhow,　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.　　 Gradually disassemble the outlet pipe, gate valve and elbow with installation tools, and tighten the next section of water pipe with pipe clamping plate. In this way, disassemble the pump section by section and lift the pump out of the well. (if it is found that there is a jam during the lifting and removal process, it cannot be lifted by force and the customer service points shall be moved up and down, left and right for safe lifting and removal)　　Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professionalRaleigh,　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, in the traditional slurry pump　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is