Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.Salzburg,SalzburgCirculating hot water pipeline pump,SalzburgQJ submersible pump,　　During the long-term overload operation of submersible sewage pumps, there are many cases of sudden abnormal failures of submersible pumps. Among them, there are some common obstacles, such as the submersible pump cannot be started after it is powered on, or the motor speed cannot be started after the submersible pump is started. A very small wait　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way canPanzos,　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, convenient disassembly and maintenance it has the advantages of simple structure, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.

　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurry　　The treatment methods are as follows: Check whether the current and voltage of the water pump are abnormal at this time. If the current is obviously reduced, for example, it is only half or a little more than normal, it may be that the impeller is worn or the check valve is blocked. If the current is not much different from the normal current, it can be　　During adjustment, firstly loosen the support cover then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationOK or not?,　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows

　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pumpsupply,　　Second, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so I　　 total depth of well or pool M　　Superior, complete protection s, reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.Salzburg,　　It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generators　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump,SalzburgCentrifugal slurry pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water