Square tubes for petroleum cracking (gb-) are furnace tubes,Torren48 galvanized square pipe, heat exchangers and pipeline square tubes suitable for petroleum refineries.Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe core rod and casing for diamond core drilling.Torren,Mechanical property is an important index to ensure the end use performance (mechanical property) of square pipe, which depends on the chemical composition and heat treatment of steel. In the steel pipe standard,Torren30 hot dip galvanized square pipe, according to different service requirements, the tensile properties (tensile strength, yield strength or yield point, elongation), hardness and toughness indexes, as well as the high and low temperature properties required by users are specified.Generally,TorrenGalvanized steel square pipe, chemical and electrolytic methods are usedSvidnik,Main uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.In recent years, large-diameter seamless square tube plays a good role in economic development. Because there are many types of large-diameter seamless square tubes, the continuous casting process of large-diameter seamless square tubes is also different. What are the specific steps of the continuous casting process of large-diameter seamless square tube? As the name suggests, square tube is a kind of square tube type. Many materials can form square tube body. Its medium is used for what purpose and where it is used. Most square tubes are steel tubes, crimped and welded to form round tubes leveled, Then the round pipe is rolled into a square pipe, and then cut into the required length. Generally, square tubes per package are mostly in large specifications in terms of spot, and . - ~~ - square tubes are divided into structural square tubes, decorative square tubes, building square tubes, mechanical square tubes, etc. according to their uses.Stage ( & mdash; )

Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust, welding slag, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale, the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.Electrochemical polishing: long specular gloss, stable process, less pollution and good durability. Suitable for mass production, it is mainly applied to high-grade products, rectangular tube and complex section square tube & mdash& mdash; Surface treatment classification of flower shaped square pipe, open square pipe, corrugated square pipe and special-shaped square pipe square pipe is divided into hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe and pickling square pipe according to surface treatment. Square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tools and equipment, machinery industry, chemical industry, steel structure, shipbuilding, automobile, square tube and thin-walled square tube plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.Development CurriculumIt is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection, and the density of steel is relatively good. After cold drawing and heating, it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust, welding slag, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale, the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.It is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection, and the density of steel is relatively good. After cold drawing and heating, it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.

Square tubes for low and medium pressure boilers (gb-) are high-quality carbon structural steel hot-rolled and cold drawn (rolled) square tubes for superheated steam tubes, boiling water tubes for low and medium pressure boilers of various structures and superheated steam tubes, large smoke tubes, small smoke tubes and arch brick tubes for locomotive boilers. Square tubes for high-pressure boilers (gb- is a high-quality carbon steel alloy steel and stainless heat-resistant steel square tube for the heating surface of water tube boilers with high pressure and above. High pressure square tube for chemical fertilizer equipment (GB - is a high-quality carbon structural steel and alloy steel square tube suitable for chemical equipment and pipelines with working temperature of - ~ ℃ and working pressure of ~ mA.superior quality,QB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, St-, etc.The advantages of real bending are small reverse, accurate forming, and as long as the roll shape is accurate, the R of inner corner forming is more accurate.B. low alloy structural steel C. ordinary structural steel and high-quality steel for specific purposes (including high-quality steel)Torren,The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.According to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!