Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, it can not only expand the physical adsorption on the pipe surface, but also enhance the mechanical adhesion between the layer and the pipe surface. Therefore, spray (throwing) derusting is an ideal derusting method for pipelines. Generally speaking, shot blasting (sand) is mainly used for the inner surface treatment of the pipe, and shot blasting (sand) is mainly used for the outer surface treatment of the pipe. Several problems should be paid attention to in derusting by spraying (throwing).San Jose Lajas,It seems that preheating the qb square tube can avoid a lot of problems, and there will be a better guarantee that the qb square tube itself is a quality problem.If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Fracha,San Jose LajasSquare pipe galvanized square pipe,Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Steel used & mdash& mdash; Such as bridge steel, boiler steel, pressure vessel steel, agricultural machinery steel, etc.Cleaning solvent and emulsion can clean the surface of square tube to remove oil grease, dust, agent and similar organic matter, but it can not remove rust, scale, welding, etc. on the surface of square tube, so it is only used as an auxiliary means in production.

Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.The purity of the square tube has a great impact on the isotropic performance of the square tube. The use of secondary refining technology (including vacuum refining, ESR and ladle powder spraying) can improve the purity of the square tube, especially reduce the content of harmful impurities in the square tube, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.Professional is king,Hundreds of degrees Celsius, which can save energy.Square pipe for conveying flammable and non flammable fluids, Standard No.: gbt (gbt - ). The representative material is l-l pipeline steel. It is mainly used to transport flammable and non flammable fluids. Low pressure or high pressure square pipes have high requirements. The purpose of large-diameter qb square pipe is qb square pipe, C-shaped steel and H-shaped steel. It is mainly used in the construction of simple plant, steel structure and other infrastructure. Qb square pipe is generally used as the frame and purlin of the plant. C-shaped steel Steel is an important support for the plant, and H-section steel is used as load-bearing. Especially in recent years, a large number of small and medium-sized enterprises have started to build spacious and bright plants. If traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises,San Jose LajasCarbon fiber square tube, if the investment in the plant is too high, the capital will be produced after operation Serious impact. The plant built with qb square tube, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, C-section steel and H-section steel have increased significantly in recent years and become the first choice for plant construction. Qb square tube, C-section steel and H-section steel are mainly used in the construction of simple plant, steel structure and other infrastructure The qb square tube is used as the frame and purlin of the plant. The C-shaped steel is used as the important support of the plant, and the H-shaped steel is used as the load-bearing. Especially in recent years, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises Said that if the investment in the plant is too high, it will have a serious impact on the capital after operation. The plant built with qb square pipe C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square pipe, C-section steel and H-section steel have increased significantly in recent years, becoming the first choice for plant construction. Large diameter qb square pipe plant is introduced Shao measures for effective wrinkle of seamless square pipe: check the wrinkle state, it should be increased to increase the inner diameter of the inner plate and the tensile stress of the wrinkle drawbead. Adopt the principle of loosening after tightening to loosen after tightening and ask Question.Stainless steel square tube for fluid transportation (gbt-) is a hot-rolled (extruded and the gradual increase of the roll gap force can be. When drawing the cone and hemispherical components, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.

Stage ( & mdash; )agent,Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.Square pipe is an important pipe. Its application in various fields has different performance. According to its different performance, we have carried out different transformation on the other pipe to ensure that the square pipe can be better used. We should make the right choice when purchasing. Below I will introduce the correct way of painting the lower pipe.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.San Jose Lajas,The principle of straightening machine is that a disc is divided into two sides to clamp round steel straight lines. Professional square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, high price, service,San Jose LajasGalvanized square pipe joint fittings, on-site settlement, honest operation! The edge is one with radius r, and the other outer edge must be two equal diameters with radius R. The diameter of the reinforcement to be straightened is D, and the center distance between them is adjusted to R + R + D.Square tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry but also can be seen everywhere in our daily life. The service life of square tubes is mainly affected by surface treatment. I will explain the specific operations of surface treatment of square tubes.Engaged in square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, old brand, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission, with standard number of gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.