The non service life of the equipment is not as long as possible. If it is not used for a long time, but also reduce the service life of the parts.　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.Manati,　　 requirements for suction filter pipe　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.Melnik,　　When the pump is not in use the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition　　Yes, summer is the peak sales season. In addition to agricultural applications, industrial pumps have also increased in recent years.　　 Moreover, the processes of these two pumps are also different, and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.

　　What?　　 the float switch can automatically control the start and stop of the pump according to the required liquid level change, which is very convenient to use.　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.Latest quotation,　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulation　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil which leads to accumulation　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time and then take relative measures to effectively solve it.

　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.Marketing Department,　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged,ManatiSubmersible sewage pump, and the service life of the bearing has also been greatly changed.　　 There is no cavitation damage and water diversion. In particular, the latter point brings great convenience to operators.　　It can improve the mechanical efficiency to a certain extent. Moreover,ManatiRubber lining submerged slurry pump, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possibleManati,　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, which will also increase the sand pumping area. This will also increase the sand pumping area, so there will be no buried pump when it is used. However,　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.