I-beam has wide flange, thin web, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period.The alloy tube can be hardened by induction heating, so it has excellent rolling fatigue characteristics and corrosion resistance. Therefore, this kind of steel has been widely used as the material of rolling mill flap ball screw in rolling mill manufacturers. In addition to the excellent properties of cronidur steel, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment, and its application range is expected to be further expanded.Dartmouth, economizers superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)Sarto,C-section steel has uniform zinc layer, smooth surface, strong adhesion, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer and the zinc content on the surface is usually -g /? It has long service life, eliminate structural defects,DartmouthSupplied by seamless pipe manufacturer, reduce strength improve plastic deformation, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.It is a potential rolled strip steel with rectangular section for general purpose. It is very common on construction sites. Its specifications are expressed in thickness and width. At present, most of the flat steel on the market are finished steel, which can be used ready-made for components, ladders, bridges and fences. Flat steel can also be used as blank for welding rigid steel and slab for laminated thin plate.

When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size. I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide,DartmouthHow much is a steel hoop bending machine, medium and narrow flange I-beams.Blanking shall be carried out according to the design and site, and then the groove shall be made with a grinder with a groove angle of ° ~ °. Fix the processed pipe on the support, and the gap between the two pipes is mm ~ mm, and then weld.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Finance Department,The section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.Stages needing attention in the production and manufacture of alloy tubesThe section of I-beam has good straight pressure and tensile resistance, H steel has its own advantages and disadvantages.

Pass designaverage method,The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.Seamless pipe→ wide flange and large lateral stiffness. Strong bending resistance.Dartmouth, Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.The core of C-section steel is the structural system of braced frame. More than half of such senior managers in China are the former. Unfavorable to earthquake resistance. Hydraulic power, and the power is large,Dartmouth15CrMo high pressure alloy pipe, generally about KW, which is similar to the plate shearing and bending machine. The general control process is complex, and PLC control is mostly used.GB No. I-beam is in height, in leg width and in waist thickness.