Wall and floor fixtures shall start at corners. According to the plate layout drawing, transport the two plates at the corner of the required device to the device location. According to the plate beam height and the model of the angle iron for fixing the mushroom head nylon bolt, drill a hole at the corresponding elevation in the middle of the plate width. When drilling, the electric drill should be perpendicular to the plate surface. Put the mushroom head nylon bolt in the hole, tighten the angle iron, and tighten it horizontally, so as to make the nylon bolt on the surface of the warehouse plate slightly concave. When setting up the wall panels, foam data and other soft data should be laid on the floor slots along with the floor of the storehouse so as to avoid damaging the storehouse. After the two corner panels are neutrally removed from the floor, the plane position of the wallboard and the verticality of the storehouse should be adjusted in time according to the location of the laying line, and check whether the top elevation of the wallboard can be correct. After the position of the wallboard is correct, weld the angle iron on the plate beam and fix the inner and outer corners. When welding the angle iron parts, the angle iron parts of the warehouse plate shall be covered with a shield to avoid the high temperature of the welding ground baking the warehouse plate and welding slag on the warehouse plate during electric arc welding.Core tip: in the cold storage project, only with sufficient cold storage installation skills can we ensure that the cold storage is more energy-saving and power-saving after installation, and is not prone to failure, convenient use and management and long service life.Fajado,The refrigeration of cold storage pays more and more attention to the needs of environmental protection and energy saving. The warehouse has a wide range of temperature control. The selection, layout and wind speed field description of refrigeration equipment are suitable for the refrigeration needs of various goods. Equipped with perfect storage temperature active detection, fan deformation; Fan motor fault; Fan motor thermal relay fault (aging); Loose wiring; Cooler blocked; Large exhaust resistance. Cold storage fault phenomenon: dryer does not operate, compressor line is disconnected, fuse is blown, thermal relay acts, high voltage switch acts, compressor is locked, line is falsely connected or loose fault phenomenon: it stops in a short time after drying, ambient temperature is too high, condenser is blockedDejen,Regular oil discharge, descaling and air discharge: when there is a .mm thick oil film in the evaporator coil, in order to maintain the set temperature requirements, the evaporation temperature will decrease by ℃ and the power consumption will increase by more than ; When the scale on the water pipe wall in the condenser reaches mm, the condensation temperature will rise by ℃ compared with the original temperature, the power consumption will increase by about . It can be seen that it is coldDuring the production of cold storage, the cold storage will produce fixed length, width and thickness according to the needs of various cold storage projects. Generally cm thick cold storage plates are selected for high and medium temperature cold storage. The requirements for cold storage engineering plates of low-temperature storage and quick-frozen storage will be higher. Professional cold storage installation, installation, construction, fruit fresh-keeping cold storage and medical cold storage ensure the quality, Guarantee service. Guarantee quality. Your satisfaction is our pursuit! Welcome to inquire. In this case, use cm or cm thick library board. When you budget the cold storage project, you can make a reservation according to the specific conditions of your cold storage temperature. If you don't make a reservation for the cold storage plate you should pay attention to the density of the cold storage plate and the thickness of the steel plate when purchasing the cold storage plate. According to regulations, the foaming density of cold storage is per cubic meterCold storage construction: which one is suitable for you? Which one is suitable for you?

Fault phenomenon: fan motor overload, fan deformation; Fan motor fault; Fan motor thermal relay fault (aging); Loose wiring; Cooler blocked; Large exhaust resistance. Cold storage fault phenomenon: dryer does not operate compressor line is disconnected, fuse is blown, thermal relay acts, high voltage switch acts,FajadoProfessional cold storage installation, compressor is locked, ambient temperature is too high, condenser is blockedThe stacking and arrangement of cargo stacks in the controlled atmosphere warehouse have a great impact on the air circulation. A basic principle of air flow is to take the path with low resistance to obtain large air flow. If there is a dead corner caused by stacking obstruction and air circulation is difficult, the temperature will rise. For this reason, there shall be gaps between the cargo stacks and between the cargo stacks and the wall. The stacking arrangement of the cargo stacks shall be coordinated with the ventilation arrangement.The structure of contemporary cold storage is in the development trend of prefabricated building cold storage. It is made into prefabricated components of cold storage including steam barrier and heat insulation plate to ensure on-site assembly. Its advantage is that the project construction is convenient, but the project cost is relatively high.Free consultation,The physical properties of polyurethane insulation board are relatively good which can meet different needs. The polyurethane insulation board is also strict in the selection of materials. It is a special product manufacturing enterprise integrating R & D, and service. It has long been specialized in cold storage installation, cold storage installation, cold storage construction, fruit preservation cold storage and medical cold storage. It improves the overall performance of the polyurethane insulation board and enables the polyurethane insulation board to work for a long time,FajadoHow much does it cost to install the cold storage, Polyurethane insulation board has also become one of the main exterior wall materials.However, long-term continuous operation will inevitably lead to equipment aging, good permeability to water vapor, foam holes, disconnected and closed porosity of more than %. It is a dense microporous foam material, which is more dense than air surface and is not easy to permeate. It belongs to hydrophobic materials.

Cold storage is mainly used for frozen processing and storage of foodMarket trend,Floor insulation of medium-sized cold storage the structure of medium-sized cold storage is what we often call the surface, that is, the top and wall are made of color steel plate / stainless steel with appropriate thickness of polyurethane and other insulation materials, while the ground needs to be insulated separately. At present, the common operations in the market are: laying the ground with XPS extruded board, laying moisture-proof and steam isolating SPS materials above and below the extruded board respectively, and then pouring concrete or reinforced concrete.For the selection of air conditioning units, it is necessary to consider the condensation pressure and other related problems of the unit, increase the proportion of outdoor cold air, and achieve the effect of energy saving.The insulation board of the cold storage adopts polyurethane double-sided color steel plate. The main effect of this cold storage insulation board is good sealing performance, insulation effect and moisture-proof effect, so as to ensure the refrigeration effect of the cold storage. The electric cold storage door is adopted for the cold storage door, and the cold storage management personnel can timely and effectively open and close the door when entering and leaving, so as to avoid the loss of refrigeration capacity of the cold storage.Fajado,Airtight construction of quick freezing storehouse: the modified atmosphere fresh-keeping storehouse is developed on the basis of the traditional high-temperature fresh-keeping storehouse, which has the & ldquo; Refrigeration & rdquo; Function, long-term cold storage installation, cold storage installation, cold storage construction, fruit fresh-keeping cold storage, medical cold storage,FajadoPharmaceutical cold storage scheme, complete products, excellent quality and favorable price. There are also & ldquo; Air conditioning & rdquo; Function; However, the quick freezing storehouse is not a simple superposition of ordinary high temperature storehouse and air conditioning equipment. In order to adjust the gas composition in the storehouse quickly, it is necessary to ensure that the quick freezing storehouse has good air tightness. This has been confirmed by the theoretical research and a large number of practical experience of quick freezing warehouse.The insulation board of the cold storage adopts polyurethane double-sided color steel plate. The main effect of this cold storage insulation board is good sealing performance, insulation effect and moisture-proof effect, so as to ensure the refrigeration effect of the cold storage. The electric cold storage door is adopted for the cold storage door, and the cold storage management personnel can timely and effectively open and close the door when entering and leaving, so as to avoid the loss of refrigeration capacity of the cold storage.Commissioning cold storage. After all parts of the cold storage are installed and connected, the cold storage can be started for cold storage commissioning. According to the needs of customers, adjust the value of the cold storage, the cooling speed and the operation of the cold storage are normal, and the cold storage can be delivered for use. The cold storage installation unit shall also provide the cold storage user with training on cold storage use and management knowledge, as well as some after-sales training.