Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be　　Generally the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but becauseSanta Ana,　　Or nodular cast iron, vertically split, bolted. The pump body is connected with the bracket with bolts. The discharge outlet of the pump can be rotated and installed at intervals of ℃ and eight angles as required.　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely,Santa AnaSubmersible sewage pump, and the delivery life will be long,Santa AnaCentrifugal slurry pump, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and writeChampasak,　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall be　　 First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use, multiple pumps need to be used in parallel or standby pumps need to be prepared.　　Only in this way can its service life be extended to a large extent.

　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　 There is no cavitation damage and water diversion. In particular, the latter point brings great convenience to operators.　　Limited. According to relevant materials, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, which makes the flow increase after the impeller is cut.Sales Department　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.　　Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but because　　Yes,Santa AnaVertical centrifugal slurry pump, such mechanical faults will cause the stator winding of the pump to be burnt out.

　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Home page recommendation,　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.　　The delivery flow of screw pump has nothing to do with the delivery pressure. The delivery pressure is only related to the stage of screw pump, while the flow and speed have a strict positive proportional relationship. Therefore, when it is necessary to control the conveying flow, it is only necessary to adjust the motor speed by equipped with frequency converter or realize stepless speed regulation by belt.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. asSanta Ana,　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.　　There are differences.