The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge. Small longitudinal crackNew San Carlos, Divided by weld -- straight welded pipe and spiral welded pipe.The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.Valencia,What should we pay attention to in the production of alloy pipeMixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal. Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, that is, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole, etc.

Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling,New San Carlos4. How much is a ton of sub welded pipe, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, the increase of specific volume will be accompanied by the expansion of workpiece volume,New San CarlosHow much is spiral welded pipe, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, the general steel pipe (black pipe) is galvanized. The galvanized pipe is divided into hot-dip galvanizing and electric steel zinc. The hot-dip galvanizing layer is thick and the cost of electric galvanizing is low, so there is galvanized pipe.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.Discount,New San CarlosHow much is cold drawn welded pipe,Stages needing attention in the production and manufacture of alloy tubesI-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, which can ensure the quality of the project. In many kinds of data we must use different raw materials, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:

The import and export order of I-beam is generally based on the specifications required in use after determining the corresponding carbon structure steel (or low alloy steel) steel grade. Except for the specification number, I-beam has no specific composition and performance series.Manufacturing cost, Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis. According to the process it is divided into arc welded pipe, resistance welded pipe (high frequency and low frequency), gas welded pipe and furnace welded pipe.I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.New San Carlos,I-beam can only be used for beam, while H-beam can be used for load-bearing column of structure. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.Alloy pipes are widely used in building materials, and the test standards of alloy pipes are also different. Alloy pipe has high hardness and can be used at many levels, most of which is prestressed reinforcement. Where plastic deformation is not specified but compressive strength is specified, such stainless steel plate can be applied.