Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.Bassett, voltage and outlet pressure every day,BassettSelf priming non clogging sewage pump,BassettTwo stage slurry pump, check the dynamic water level every two weeks and make records.　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons,BassettQJ submersible pump, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.Dedza,　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion, which is convenient and flexible.

　　Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.　　cf fire control cabinet is a cabinet that controls the startup and shutdown of fire pump and other operating s. It gets rid of the complex and difficult operating procedures of the previous single fire pump startup and shutdown, so really　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pumpHonest service,　　 During the installation of smooth bearing components, if the installation is correct the smooth oil is appropriate, the repair is timely, and the delivery life will be long, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.

　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Where can I find it?,　　Carbon building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.　　The course can be stronger.　　What is the solution to this situation?Bassett,　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water