The wear resistance, fracture toughness, impact toughness and bending strength under different process conditions were compared and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Halley,The surface of cold galvanized layer is smooth, dense and uniform. It has good mechanical properties and corrosion resistance. The consumption of hot-dip galvanized coating is between % - %. The galvanizing process is complex, but the thickness of single-sided coating, surface coating and double-sided coating is different, so the thin-walled pipe shall be galvanized. The zinc coating has strong protection and corrosion resistance.It is widely used in various fields of national economic construction, such as buildings, bridges,Halley76 seamless pipe price, power stations, oil drilling platforms, vehicles, highways, subways, steel structure plants and large warehousesShakyarabadinPlan option : Martensitic chromium alloy pipe,Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing, siliconizing and so on are commonly used in production.d. All machines and equipment in a production line can connect with the software of the computer data collection system to complete the timely transmission of data information, and the performance parameters in the production process are monitored by the central control room.

H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for settingLongitudinal welded pipe has the advantages of simple production and processing technology, high production efficiency,HalleyAlloy pipe quotation, low cost and rapid development trend. The compressive strength of spiral welded pipe is generally higher than that of straight welded pipe. Narrow blank can be used to produce welded pipe with large pipe diameter, and blank with the same total width can also be used to produce welded pipe with different pipe diameter. However, compared with the straight seam pipe with the same length, the welding length is increased by ~ , and the production rate is low.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production,HalleyHow much is a welded pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.recommend,I-beam is a long strip steel with groove section, which belongs to carbon structural steel for construction and machinery. It is a section steel with complex section, Baotou Iron and steel Shangang, huangte, Maanshan Iron and steel, Japan iron and steel etc.I-beam is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'.I-beam is a kind of economical section steel with better section mechanical properties. Its characteristics are as follows:

Function of I-beam: where is I-beam mainly used?Potential development,Alloy pipe can be divided into round steel pipe and special-shaped steel according to different cross-sectional area. Because the circular area is large on the premise of the same side length, a large amount of liquid can be transported with an annular tube. In addition, when the circular cross section bears the internal or external axial working pressure, the bearing force is more symmetrical. Therefore, most seamless steel pipes are round steel pipes.The use of welded steel mesh in China is still in its infancy. At present, the use of welded steel mesh in China accounts for less than one of the total amount of steel reinforcement. In the early s, steel welded mesh was listed as a key implementation project by the science and Technology Commission and the Ministry of construction, and specifications and procedures were formulated.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Halley, Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.