Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled,GuadalupeSplit vertical pipeline pump, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored,GuadalupeVertical non clogging sewage pump, it should continue to be used after maintenance. Do not dump it directly　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.Guadalupe　　During normal operation, the impeller of the slurry pump becomes tighter and tighter as it turns. The more it is used, the easier it will operate. However, if the slurry pump reverses, installed and tested.　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simpleZarumilla,　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.　　 Next, the water seal, lock ring and other parts need to be installed.

　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, it is inconvenient to repair.　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the waterbuild,　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in use　　Troubleshooting: first increase the water pressure then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.

　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, whenFor more, please check,　　How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.　　Structural features of horizontal slurry pump: The ah, HH and L-type slurry pumps at the pump head are of double pump shell structure, that is, the pump body and cover are equipped with replaceable wear-resistant metal lining and the flow passage components such as impeller, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time,GuadalupeFire deep well pump, and then take relative measures to effectively solve it.Guadalupe,　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.　　If the oil seal ring of the shaft is seriously worn