Small blisters can not be repaired after damage, and the upper foot is weak. The conventional thickness is only -mm. The ultra-thin design is a bold innovation in the professional industry. The surface is printed with materials to improve the service life of people flow field. The surface imitates the real wood texture and natural marble texture. In view of the characteristics of raw materials, it has fast heat conduction and long heat storage duration. It is the preferred floor for floor heating.SanPedrodeMacoris,Wear resistant paper invented in the s was used on the surface of bowling alley.Because of the creation, invention and application of anti-static laminate flooring products, European manufacturers use wear-resistant paper to strengthen the production and manufacture of anti-static flooring, and take it as a key component to strengthen anti-static flooring.At present, the domestic rate of wear-resistant paper in China has reached about %, but it still needs to be imported.The key index values for evaluating the quality of wear-resistant layer are:Direct contact with formaldehyde can cause skin allergy, pigment spots and atrophy. Inhalation of high concentration formaldehyde can cause chronic bronchitis.Kintampo,In order to reduce the cost, which has poor stability and large thermal expansion and cold contraction.The loss is caused by the 'general paving method'.The wear resistance of laminate floor mainly depends on the content of aluminum oxide in the surface layer, and a certain number of wear-resistant revolutions corresponds to a certain content of aluminum oxide.For household floors, the number of wear-resistant revolutions is usually more than revolutions,SanPedrodeMacorisHow to clean the floor leather, while in public places, it is usually more than revolutions. You can buy it on demand. Produce gene mutation effect.

Ultra light and ultra-thinSPC floor has a variety of colors, such as blanket pattern design,SanPedrodeMacorisFloor rubber board and floor leather, stone pattern design, etc.,Even be able to complete personalized customization.The wireframe is real, beautiful and generous. Equipped with a variety of accessories and decorative design strips, it can integrate the practical effect of beautiful and generous decorative design.Now we have VSPC flooring, and another layer of processed bamboo is basically attached to SPC, which makes the floor tone milder and feel more comfortable.Third, it is flame retardant, but it can&#;t be burned.Pursuit of excellence,Foot feelThe first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :,SanPedrodeMacorisDo you want anything under the SPC floor, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed they can be wiped with alcohol.In this way, the grade of interior decoration is also rising the whole process will be completed.Due to the improvement of the living standards of Chinese residents, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth. Pay attention to the size.

Wear resistance, wear resistance grade t.Workshop cost, Green environmental protectionSmall blisters cannot be repaired after they are destroyed. A foot pad shall be placed in front of the door to reduce the wear of sand on the floor.SanPedrodeMacoris, Remove spots and stains with special floor cleaner.Do not clean with items with damaging properties, such as metal tools, nylon friction pads and bleaching powder.Generally, the moisture content of non dry wooden keel is about %, and that of qualified wooden floor is generally about %. If the humidity difference is too large, the wooden floor is easy to absorb moisture quickly. If the time is long, the floor will arch up and the paint will crack.Therefore, it is best to choose dry and straight wood as keel.After the keel level is determined the keel and floor can be fixed with nails.If you want to polish a lot of things, tarpaulin and tape.Hardwood floors often need to be polished during installation.