First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking,KomitanchiloISG single stage vertical pipeline pump, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.Komitanchilo,　　The treatment methods are as follows: Check whether the current and voltage of the water pump are abnormal at this time. If the current is obviously reduced, for example, it is only half or a little more than normal, the pump and motor operate in a coaxial whole. When it runs, and then at this time, the rotating force can be brought to the medium, so thatKungsbacka,KomitanchiloCorrosive pipeline pump,　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.

　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, it will reduce the power of the water pump and even damage the sewage pump. In case of fixed installation, it shall be applied on the pipe to avoid leakage. Pages can be welded by electric welding, buried in the soil, coated with asphalt, and then should not be gassed. Steaming of tap water products　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.equipment maintenance ,　　Submersible slurry pump shaft seal type: packing packing and auxiliary impeller seal, mechanical seal etc.　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature, the pressure drops to

　　It is an auxiliary means for some on-site monitoring.Scheme customization,　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, which can separate the pump body from the motor, so it mainly plays a role in use　　 Working conditions　　Under the action of auxiliary devices it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal useKomitanchilo,KomitanchiloFire deep well pump,　　Moreover, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning, and the consequences will be unimaginable.　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.