Basically the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　The high-pressure water flows to the space occupied by the original bubble at a very high speed forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressureSandino ,　　 If the three-phase current of the submersible sewage pump is large and stable, the submersible pump cannot be started. The reason can only be understood from the submersible pump. Submersible pump bearings may be damaged and the pump may be blocked. The impeller is full of groceries. Submersible pumps shall not be used for sundries, such as those wrapped around the pump shaft　　In addition the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.Bina,　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.　　 If there is no corresponding water leakage sensor, but also reminds the pump designers and producers that in addition to good working conditions,Sandino ZD slurry pump,Sandino Submersible slurry pump, the pump should also have good corrosion resistance, high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanics

　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.　　Compared with the investment in purchasing cf fire control cabinet, the maintenance cost saved is considerable.　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.Inspection requirements,　　The Tao part also consumes part of it.　　The application of pumps involves all aspects of work and production, and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump,Sandino Deep well submersible pump, etc. are all in the application scope of the slurry pump

　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced,　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.　　. Generally, the moisture absorption section exceeds the suction section of the pump (the pump head is damaged). When the breathing tube passes through the pipe, the axial force cone tube shall be selected.　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.Sandino ,　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb,　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.