It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment　　 In addition,PalmiraQuotation slurry pump, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.Palmira,　　Solution: replace the remote pressure gauge; Replace the pressure transmitter; Check the connecting signal wire.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motorMutuali,　　The other mechanical seal is a split seal, which can be replaced without disassembling the slurry pump.　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, the service life of the flow passage parts of the pump is relatively long, saving production costs.　　 Pipeline booster pump: in fact, the pipeline booster pump is what we often call a booster pump. It is named according to the purpose of the pump. As the name suggests,PalmiraHorizontal wear-resistant slurry pump,PalmiraSubmersible non clogging slurry pump, any pump that can pressurize the liquid delivered in the pipeline can be called a pipeline booster pump. Not limited to one type of pump, such as centrifugal pump, pipeline　　 Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.new product,　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!　　It is located in the middle, so it seems that many regions have good effects when using it.　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall be

　　 Then reinstall the equipment on the engine and install the rubber hose.Meticulous workmanship,　　Occurrence of personal injury accident. The slurry pump is mainly used to transport water or similar media when in use. It can also be regarded as a common pump in our life, but it will also be overloaded when in use. Let&#;s have a look today　　Domestic stainless steel pipeline pump products have greatly improved their technical level through introduction, absorption, digestion and innovation. In particular, the supporting products of some major technical equipment have reached or approached the advanced level of similar products. With the continuous expansion of the market, stainless steel pipeline pump　　The high-pressure water flows to the space occupied by the original bubble at a very high speed forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressurePalmira,　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speed　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.