Miscellaneous scabSo why is the alloy pipe easy to rust after being pickled and passivated by the software?Libertaborg,Next, let&#;s introduce the operation steps of roll adjustment during roll change. First of all, replace the complete set of rolls. The adjustment process of the rolls is as follows: first, draw an axis from the channel of the generator set to the import and export with stainless steel wire for adjustment, so that the holes of each frame plate are on the same axis, and the bottom line of forming ethics meets the technical standards.The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition,Libertaborg15CrMoG high pressure alloy pipe, I-beam can also adopt special rolling method.AtuntaquiThe general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.GB No. I-beam is in height, in leg width and in waist thickness. Peak crack

C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover, it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibilityIn the production process, the stainless glittering pipe is affected by the outside and product surface. Due to galvanizing, the corrosion protection is not corroded. This is the thickness of zinc, and the quality and strength of its coating depend on longevity. Miscellaneous scabequipment maintenance ,Pass designDehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlement Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.

Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.Potential developmentAlloy pipes can be used for heating (cooling) projects. General carbon steel wire sleeve (GB / t- is a steel pipe used to protect wires in electrical installation projects such as industrial and civil buildings and installation of machinery and equipment.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane,Alloy tube is widely used in our daily life,Libertaborg15CrMo seamless pipe manufacturer, which provides us with great assistance.The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.I-beam has wide flange, thin web, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period.