→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.Heating surface pipes, economizers, superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)Permanent gem, Straight seam electric welding steel pipe (yb- is a steel pipe whose weld is longitudinally parallel to the steel pipe. It is usually divided into metric welded steel pipe, welded thin-walled pipe, transformer cooling oil pipe, etc.The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.Long-Beach, Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Difference and application description between H-beam and I-beam

The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.There are many processes in the process of welded pipe processing, and every detail needs our attention. Welded pipes need to be treated by various processes before application. Heat treatment of welded steel pipe is an important link in the process of welding steel pipe. Hot working is a metal hot working process in which metal materials are heated, insulated and cooled in a certain medium, and the metal properties are controlled by changing the metallographic structure on the surface or inside of the material.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, meet the requirements of thermal insulation and cold protection, reduce heating equipment unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Pursuit of excellenceI-beam: national standard * what is the wall thickness of I-beamThe general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy,Permanent gemQ345B seamless pipe factory,Permanent gemE how much is the steel bar turning software, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.

I-beam: national standard * what is the wall thickness of I-beamWelcome calls ,When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size. It has iron zinc alloy layer and compact combination, which shows unique corrosion resistance in marine salt spray atmosphere and industrial atmosphere;When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.Permanent gem,Permanent gem13crmo4-5 alloy pipe,Main uses: as a finished material, flat steel can be used to make hoop iron, tools and mechanical parts and used as building frame structural parts and escalators in buildings. Flat steel is divided into two types according to its shape: plane spring flat steel and single-sided double groove spring flat steel. Hot rolled spring flat steel is mainly used to manufacture leaf springs for automobiles, tractors, railway transportation and other machinery.The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate. Small longitudinal crack