Method of forging solid wood floor Convenient installation and operation: the installation of solid wood composite floor is the same as that of laminate floor, without keel. As long as the ground is flat, the building height can be improved.In addition, due to the simple installation regulations, the safety hazards caused by installation are also greatly reduced.Solid wood flooring has high environmental protection, health and comfort, and is deeply loved by many small partners.Solid wood flooring has many advantages,Manufacturers generally consist of four layers of raw materials, namely wear-resistant layer, decorative layer,Common cost methods for solid wood flooring are as follows: Veneer method: stick the wood veneer on the board surface.For example, the high price solid wood veneer is pasted on the low price solid wood floor. Although this is also the solid wood floor, it deceives consumers.The commonly used floor is generally mm thick, and the .mm wear-resistant layer locks the floor.Such a thick floor generally does not have the situation that the door cannot be closed or affect other s the material will not be very expensive, the foot feels comfortable, the service life is relatively long, there will be a series of problems with wood flooring.Floor cracking is a common method.Today, we will discuss why the wood floor cracks.

The cross-section of the floor is rubbed with a file to generate heat in the cross-section, and formaldehyde is fully volatilized (formaldehyde is accelerated at more than degrees, and you can smell the pungent smell at the same time). At this time, you can smell, generally you can smell three different levels of smellIt is simple to clean, bright as new, dirt free and easy to clean. The surface of solid wood reinforced composite floor is painted and treated very well, with good wear resistance, and does not need to spend a lot of energy on maintenance. It is reported that good solid wood composite floor in the market can keep the paint bright as new without waxing within years. This is in sharp contrast to the shape and maintenance of wood floor.The cross-section of the floor is rubbed with a file to generate heat in the cross-section, and formaldehyde is fully volatilized (formaldehyde is accelerated at more than degrees, and you can smell the pungent smell at the same time). At this time, generally you can smell three different levels of smellInspection requirements, Look Whether to renovate the board.When laying wooden floor, pay attention to the length and direction of the floor consistent with the entry direction to ensure good visual effect.First, choose the brand you need (i.e. grade);

SPC floors are subject to biological resistance treatment, and the unique sealing of the surface layer makes the products have the characteristics of anti bacteria and antibacterial, and meet the cleaning requirements of various departments and institutions.When it comes to the choice of decoration flooring, you can think of ceramic tile, marble and wood flooring. However, SPC flooring has become the first choice for people to buy Flooring in developed countries and regions such as Europe, America, Japan and South Korea, and the domestic market is gradually accepting SPC flooring. Why SPC flooring is popular? First of all,PinskHow to deal with the blackening of wooden floor, what is SPC flooring and how about SPC flooring,Now let&#;s learn what SPC floor is and how SPC floor is.SPC is the abbreviation of stone plastic composites (stone plastic composites). The main raw material is polyvinyl chloride resin. It is made by extruding SPC substrate by extruder combined with T-shaped die, and heating, laminating and embossing PVC wear-resistant layer, PVC color film and SPC substrate by three roll or four roll calender at one time. Glue is not used in the production process.Test results, Beautiful and diverse colors, seamless splicing construction, convenient and fast installation.How to buy solid wood composite flooring?The most common causes of wood floor cracking are the moisture content of the floor and the dry humidity of the environment. For example, the moisture content of the wood floor is % and the local average moisture content is %. In order to balance the moisture content of the floor and the moisture content in the air, the dry air absorbs moisture from the wood floor, and the wood floor cracks in this processPinsk, Non toxic and tasteless, not afraid of water, fire and tide;In terms of scratch resistance, resource use and anti-skid performance, SPC floor is better than laminate floor. Test: for the ground lacquer cloth with thin thickness, you can tear it by hand. If it can be easily torn off, if it can not be restored to the original state and leave an indentation, such a product has poor softness.If the layers can be torn by hand, it indicates that the product layers are not well combined, and stratification will soon occur in future use.Plastic floor paint cloth has the advantages of light weight, elasticity, good mechanical strength good foot feeling strength, comfortable foot feeling, wear resistance, pollution resistance, corrosion resistance, heat insulation, sound insulation, moisture resistance, small water absorption, good insulation, self extinguishing, easy cleaning, simple construction, convenient maintenance and low price. In a large number of civil buildings and public places it has high requirements for cleanlinessIt is widely used in the laboratory.Plastic floor paint cloth belongs to soft floor. It is a floor coil produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.The length of each roll of plastic floor paint cloth is m ~ m, and the total thickness is mm (machine room) ~ mm (plant and public buildings)For long-term indoor use the width is mm ~ mm ~ mm, high and medium grade products should be selected, and products produced by well-known brands and regular enterprises should be purchased as far as possible. Such products have sufficient thickness and good interlayer adhesion, and are not easy to layer and curl, especially foamed leather which gives people a comfortable and elegant feeling. If you want to use them for a short time or one-time cover, you can choose low-grade products, because low-grade productsThe price is low and there are many prices to choose from, but many of these products are processed with waste materials, with poor flexibility, it should be under scattered sunlight or fluorescent lamp, and the illumination should be ( ± LX, LM from the tested sample, conduct oblique visual inspection. First, observe whether there are cracks, fractures and delaminations on the surface of the local lacquer cloth. If there are, it can be judged that the local lacquer cloth is unqualified. The second step is to observe whether there are wrinkle marks,PinskWhich is better, laminate floor or composite wood floor, bubble pollution points and pattern deformation. Those that cannot be observed are excellent products and first-class products; those that are slight but not obvious are recognized as qualified. Go back to the third step for observationIf there is any missing pattern on the surface of the ground lacquer cloth, or if there is any defect of the transparent wear-resistant film on the surface, it is the first-class product and the first-class product. If there is a slight missing print or lack of film, it is the qualified product, otherwise it is the unqualified product. Finally carefully check whether there is deviation in the multi-color overprint on the surface, whether there is color difference in different parts, if the top-class product is uneven, if there are the above two defects but if there is no obvious, it is the first-class productProducts that obviously have the above defects but do not affect the overall beauty are judged as qualified products. Finally, the appearance quality of ground lacquer cloth is determined based on the above judgment. When selecting ground lacquer cloth,PinskWhich is better, solid wood floor or laminate floor, first smell whether it has pungent smell. There will be a slight smell after the good coil is opened, and the smell of inferior products is stronger; secondly, calculate the use area, and the same room should be selectedCoiled materials with the same batch number, pattern and thickness. When purchasing, carefully observe the appearance quality, open a roll of ground lacquer cloth, separate the ends for a few meters, observe the surface layer of the sample, the surface layer is thick, and the service time is long, and then observe whether there are cracks, fractures, wrinkles, bubbles and large defects; whether the cross section is layered and cracked; whether the pattern is open, missing, color difference and pollution. Generally, wear-resistant paper with aluminum oxide content of about g / m is used, or wear-resistant paper is not used.Low density board (medium density board is rarely used), and the number of wear-resistant revolutions is usually between - revolutions.The edges and corners will be worn after being used for one or two years at most.With Hunan, Hubei, Shandong, Liaoning, Jilin and Heilongjiang as the gathering points, the suburbs of Beijing are still rampant.Low quality, not environmental protection, government departments are strictly investigating and dealing with it.Such illegal businesses only take into account short-term interests and have no after-sales service guarantee. The price ranges from to yuan.