Xhy- series high hardness alloy I-beam; Undertake drawings and process wear-resistant pipes（ Φ ≥mm）； Undertake the processing and production of vulnerable parts of cement machinery; Welding technology consultation and service; The wear-resistant layer of alloy wear-resistant plate of high chromium heap welding flux cored wire series is mainly high chromium, as well as manganese, molybdenum, niobium, francium and other components. The alloy carbide formed has strong stability at high temperature. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time,Idler pipe: it is used for electric welding steel pipe of idler of belt conveyor. It is generally made of Q, QA, B steel and steel, with a diameter of -mm. There are certain requirements for pipe tortuosity, end face straightness with the center line and ovality. Generally, water pressure and flattening tests are carried out. Small longitudinal crackKampala,Heating surface pipes, economizers superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃) The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, such as various alloy steel plates, cast stones, rubber, polyurethane, etc., it has irreplaceable comprehensive excellent properties.

Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength,GomelWhere is there a place to sell steel bars nearby, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process it will eventually lead to bad harm to the product quality.The electric welding reinforcement mesh can reduce the damage and consumption to the reinforcement processing process. According to statistics, it can also save about % of the steel. After it is transported to the site according to the construction degree of the project after deducting the steel consumption increased by unit lapping, it can be hoisted to the working face. There is no need to set a reinforcement processing site on the site, which saves the site and increases the management level of the site. At the same time, it can also solve the problems of noise pollution caused by straightening reinforcement. H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.Welcome calls ,H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, better mechanical properties per unit weight, light I-beam has narrower legs, thinner waist and lighter weight than ordinary I-beam. No. - is large I-beam,GomelHow much is 150 galvanized pipe 1 meter, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications, dimensions and relevant standards.It is widely used in various fields of national economic construction, such as buildings, bridges, power stations, oil drilling platforms, vehicles,GomelHow much is 12 I-beam per ton, highways, subways, steel structure plants and large warehouses

Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.Convenient and efficient,Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.The surface of cold galvanized layer is smooth, dense and uniform. It has good mechanical properties and corrosion resistance. The consumption of hot-dip galvanized coating is between % - %. The galvanizing process is complex, but the thickness of single-sided coating, surface coating and double-sided coating is different, so the thin-walled pipe shall be galvanized. The zinc coating has strong protection and corrosion resistance.Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.Gomel, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected. Judged as failing.