The selection of pipes and fittings for welding data preparation shall be based on the quality elements of the application environment, chemical composition and application pressure, and the commodities of corresponding grades shall be selected to ensure the weld metal structure and machine function.Therefore, there are requirements for the service environment of stainless steel,　　— The corrosion resistance is the same and the strength is better because the carbon content is relatively high.Hardness test: annealed stainless steel pipes with inner diameter of more than mm and wall thickness of less than mm can be tested by w-b Vickers hardness tester, which is very fast and simple, and is suitable for rapid and nondestructive qualification test of stainless steel pipes. For stainless steel pipes with inner diameter of more than mm and wall thickness of more than mm, Rockwell hardness tester shall be used to test HRC hardness. Stainless steel pipes For stainless steel pipes with inner diameter greater than mm and wall thickness less than mm, the surface Rockwell hardness tester shall be used to test HRT or hrn hardness. For stainless steel pipes with inner diameter less than mm and greater than mm, the special Rockwell hardness tester for pipes shall be used to test hrt hardness. When the inner diameter of stainless steel pipes is greater than mm, the Rockwell or surface Rockwell hardness tester can also be used to test the hardness of pipes.Nyaungdon,. It is our responsibility not to pay attention to the maintenance of the pipe during transportation, mix the pipe with corroded chemical commodities, or soak the two water into the packaging film during transportation in rainy days, which will cause rust. . It is the responsibility of the processor and manufacturer. When cutting stainless steel or iron when manufacturing goods, the scrap iron will cause rust on the surface of the steel pipe. Therefore, it is only reasonable for highly skilled technicians to deepen investigation and discussion, make a reasonable division of responsibilities, and who should be responsible for whose achievements. You can't let steel mills, pipe factories, processors, or users bear the liability for compensation!The corrosion resistance of stainless steel depends on chromium, but because chromium is an integral part of steel, the protection is different.Meet the needs of architects and structural designers.

Model & mdash& ldquo; Cutting tool level & rdquo; Martensitic steel, an early stainless steel similar to Brinell high chromium steel. It is also used for surgical tools, which can be made very bright. Model & mdash; Ferritic stainless steel for decoration, such as automotive accessories. Good formability, but poor temperature resistance and corrosion resistance.The Chinese brand cold rolled non oriented silicon steel strip (sheet) represents: DW + times of iron loss value (at the frequency of Hz, the waveform is sinusoidal, and the magnetic induction peak is T per unit weight iron loss value) + times of thickness value. For example,BarysauStainless steel compression elbow, outer diameter and wall thickness. Compared with argon arc welding, it is more than ten times its high welding speed. Therefore, stainless steel pipes for common use have a higher consumption rate. Due to the high speed of high frequency welding, it is difficult to remove burrs in welded pipes. At present, high frequency welding Welded stainless steel pipe can not be borne by chemical and nuclear industries,Stainless steel why corrosion-resistant stainless steel decorative pipe, stainless steel pipe, stainless steel pipe, all metals react with oxygen in the atmosphere to form an oxide film on the surface. Unfortunately the iron oxide formed on ordinary carbon steel continues to oxidize, expanding the corrosion and finally forming holes. The carbon steel surface can be guaranteed by electroplating with paint or oxidation resistant metals (e.g. zinc, nickel and chromium) but as is known, this protection is only a thin film. If the protective layer is, the steel below begins to rust.When the stainless steel pipe with solid core welding wire is prefabricated, the welded junction can usually be rotated for welding, and the ventilation is very easy. At this time the blocking plate is usually used to block both sides of the welded junction in the pipe, and the bottom welding is carried out for the protection of ventilation (see Table ), stainless steel coil, stainless steel belt and stainless steel pipe to avoid price difference. The price is % higher than the market price! The price of more than one ton is higher! So that the nickel bath can not get the ideal bright nickel coating, it is necessary to carry out large-scale treatment. In the solution of bright nickel plating on stainless steel pipe, the development of brighteners has experienced four generations. Instead of the original product, saccharin and butynediol can be plated with bright nickel with high flatness. Its application flourished in the s and s. It seems that due to the instability of butynediol in the nickel plating bath, short service life and rapid accumulation of organic impurities, the nickel bath needs to be treated frequently. Therefore, epoxy chloropropyl or epoxy is branched with butynediol to synthesize the second-generation nickel plating brightener such as b brightener. The situation has improved. Be and retain alkynyl. Later, pyridinyl is polymerized to form the third-generation product, Faster light output, less amount of brightener and longer service life. Now it further uses various combinations of nickel plating brightener intermediates to form a new brightener,Barysau304 stainless steel pipe welding method, which has developed to the fourth generation of products. It has less use, faster light output speed and longer treatment cycle. According to the connection and rolling process, stainless steel pipes with deep plating capacity mainly include hot-rolled, hot-rolled and cold drawn (rolled) stainless steel pipes. According to the difference of metallographic structure of stainless steel, it mainly includes semi Ferritic and semi martensitic stainless steel pipe, martensitic stainless steel pipe, austenitic stainless steel pipe, austenitic ferritic stainless steel pipe, etc.Sales Department,There are three main reasons for oxidation of stainless steel: production process, which is one of the reasons for oxidation of steel products. In terms of production process and product characteristics, forming a thin oxide film on the product surface is the basic process to avoid oxidation, and it is also one of the main characteristics of steel products different from other steel products. It is specialized in products, renewable resources business and business package Including: stainless steel plate, stainless steel coil,Barysau316L stainless steel round pipe, stainless steel belt and stainless steel pipe. However, when the oxide film is incomplete and discontinuous due to insufficient or negligent production process, the oxygen in the air will directly react with some elements in the product, resulting in the appearance of oxidation of the product.Its plastic toughness is lower than that of austenitic stainless steel, and its cold and hot working process and formability are not as good as that of austenitic stainless steel.Stainless steel pipe packing bag is nothing more than the function of protecting the surface of stainless steel pipe, so most stainless steel pipe users do not have to question this point.Barysau,Some reasons for product composition ratio: in order to reduce the production cost, reduce the proportion content of some important elements such as chromium and nickel, and increase the content of other elements such as carbon. This production phenomenon that the composition ratio is not strictly in accordance with the product model and product characteristics not only greatly reduces the product quality, for example, when the chromium content of stainless steel pipe is insufficient, it not only affects the production The corrosion resistance and formability of products have potential product quality and safety hazards when they are used in chemical, equipment and production industries. At the same time, they also affect the appearance and oxidation resistance of products.During welding, the process of ventilation in advance and gas stop behind shall be adopted, and the adhesive cloth on the outside shall be torn off while welding. Because the blocking plate is composed of rubber and white iron sheet, it is not easy to be damaged, so this welding can well ensure that the inner side of the weld is filled with argon and its purity, so as to effectively ensure that the metal on the inner side of the weld is not oxidized and ensure the quality of weld backing welding.Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, the heating temperature shall not exceed ℃, so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.