Stainless steel has two classifications: one is divided into chromium stainless steel and chromium nickel stainless steel according to the characteristics of alloy elements; The other is divided into m stainless steel, f stainless steel, workbench, towel hanging bracket and bracket of refrigerator in daily life is increasing.Schweichard,Under plasma arc cutting corrosion conditions,SchweichardStainless steel embossed tube, there are dust containing other metal elements or attachments of dissimilar metal particles on the surface of stainless steel. In the air, the condensate between the attachments and stainless steel connects them into a micro battery, which causes electrochemical reaction and the protective film is affected, which is called electrochemical corrosion. the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the steel plant is that the peeling and trachoma of the steel strip will cause rust. Substandard materials will cause rust. the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the pipe manufacturer: the welds in the pipe manufacturer are polished rough, which will cause rust.Heerenveen,Model & mdash; Commonly used precipitation hardening stainless steel model, usually also called -; %Cr,%Ni.Model & mdash; Cheap model (British and American), usually used as automobile exhaust pipe, is ferritic stainless steel (chromium steel).Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content the greater the tendency of intergranular corrosion. In addition, intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich CrC on the grain boundary. The chromium poor area is formed in the surrounding matrix, which is referred to as - steel for short. Its characteristic is that the carbon content is less than .%, and the single-phase austenite structure is obtained by the combination of Cr and Ni.The surface quality appearance and dimensional accuracy of cold rolled steel strip are better than those of hot rolled plate.Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, the heating temperature shall not exceed ℃ so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.DiscountDuplex stainless steel product description: This stainless steel has good corrosion resistance in urea carbamate solution and high stress corrosion cracking resistance in chloride environment. At the same time, the duplex stainless steel has excellent mechanical properties and can be used in plant construction with high safety requirements.Model & mdash; The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.The back is blocked with blocking plate for ventilation protection; Only soluble paper or the combination of soluble paper and blocking plate is used for blocking ventilation protection; Use flux cored wire for backing TIG welding.

Adjust the ratio of austenite forming elements to ferrite forming elements in the steel to make it have austenite + ferrite dual phase structure, in which ferrite accounts for % - %. This dual phase structure is not easy to produce intergranular corrosion.High quality and low price,There are mechanical, chemical and electrochemical methods to remove the scale of stainless steel pipe. Due to the complexity of the composition of the scale of stainless steel pipe, it is not easy to remove the scale on the surface and make the surface highly clear and flat. Generally, the removal of the scale of stainless steel pipe should be carried out in two steps, the first step is pretreatment and the second step is ash removal.Spcespce & mdash; & mdash; refers to cold-rolled carbon steel sheet and strip for deep drawing, equivalent to China Al () deep drawing steel. If it is necessary to ensure non aging property, add n at the end of the brand as spcen. Quenching and tempering code of cold-rolled carbon steel sheet and strip: annealing status is a, standard quenching and tempering is s, / hard is / , hard is / , bright finish rolling is B. spcc-sd represents cold-rolled carbon sheet generally used for standard quenching and tempering and matt finish rolling. Another example is spcct-sb It refers to cold-rolled carbon sheet with standard quenching and tempering and bright processing and required to ensure mechanical properties.Adjust the ratio of austenite forming elements to ferrite forming elements in the steel to make it have austenite + ferrite dual phase structure, in which ferrite accounts for % - %. This dual phase structure is not easy to produce intergranular corrosion.Schweichard,Since the back is not filled with argon, its advantages are obvious,SchweichardPrice of stainless steel plate in 2015, mainly for its simplicity and low cost,Schweichard254SMO stainless steel pipe, which is suitable for installation on the construction site. However, due to its structural characteristics, flux cored welding wire has high requirements for welders during operation, with fast wire feeding speed and high wire feeding accuracy. It is difficult to master. Welders should be specially trained and skilled before they can participate in welding in Yangba, Nanjing And foreign construction sites, we have successfully solved the problem that argon cannot be passed through the junction and repair port.When the stainless steel fixed port is welded, it will be difficult to ventilate on both sides of the weld. At this time, how to ensure the argon filling protection on the inner side of the weld has become a difficult problem. For a long time, facing the national high price, the reasonable price and perfect service of all kinds of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel pipes have been recognized by the majority of customers. In the actual construction on site, we use two welding joints The above problems were successfully solved by plugging with water-soluble paper on the side, ventilation from the weld center and sealing with adhesive tape on the outside (see Table ).CE--“ Code for design of cold formed stainless steel structural parts & rdquo; And & ldquo; jointly published by nidi and euro inox; Structural stainless steel design manual & rdquo; The design of structural parts for buildings with long service life and good integrity has been simplified.