Technical assurance measures for the installation of cold storage: during production in the production workshop, the production shall be carried out in strict accordance with the operation rules specified in ISO quality operation, self inspection and inspection application shall be carried out to ensure that the factory pass rate is, and unqualified products are not allowed to leave the factory.The insulation board of the cold storage adopts polyurethane double-sided color steel plate. The main effect of this cold storage insulation board is good sealing performance, insulation effect and moisture-proof effect, and the cold storage management personnel can timely and effectively open and close the door when entering and leaving, so as to avoid the loss of refrigeration capacity of the cold storage.Santa Barbara,An air duct is generally set in the vegetable cold storage. The air flow from the upper air duct mouth blows to the wall and the lower product line, returns to the middle, is absorbed by the lower part of the evaporator, and the evaporator drains and returns to the air duct again.Compression refrigerator is commonly used, which is mainly composed of compressor, condenser, throttle valve and evaporation pipe. According to the way of evaporation pipe device, it can be divided into direct cooling and indirect cooling. Direct cooling the evaporation pipe is installed in the refrigerated warehouse. When the liquid coolant passes through the evaporation pipe, it will directly absorb the heat in the warehouse and cool down.Enfield Town,The refrigeration of cold storage pays more and more attention to the needs of environmental protection and energy saving. Professional projects include: cold storage installation, installation of cold storage, cold storage construction, fruit fresh-keeping cold storage, medical cold storage and other related businesses. Merchants who hope to have this business please consider the wide scale of warehouse temperature control, recording and active control equipment.General quick-frozen warehouses are mostly cooled by refrigeration mechanisms, and those with very low gasification temperature are used as coolant to evaporate under low pressure and mechanical conditions, so as to absorb the heat in the warehouse, so as to achieve the purpose of cooling and reduction.Cold storage has good water tightness. Polyurethane rigid foam has low water absorption, good permeability to water vapor, foam holes, disconnected and closed porosity of more than %. It is a dense microporous foam material, which is more dense than air surface, and is not easy to permeate. It belongs to hydrophobic materials.

The water tank is designed to be separated from the machine body and is double-layer. It will not drip due to condensation caused by internal and external temperature difference. It can be interlocked with the refrigeration system, that is, it will not be humidified during refrigeration to prevent serious frosting of the fan.With the continuous development of cold chain industry, the construction scale of logistics cold storage is expanding, and the construction quantity is also increasing. According to statistics, at present, the performance growth rate of cold chain is maintained at % ~ %; This leads to the increasing demand for logistics cold storage. In the design of logistics cold storage, so as to ensure its functions in product freezing, refrigeration, insurance and so on.In the low temperature environment, especially in the periodic freezing and thawing cycle, the building structure is also vulnerable to. Therefore, the building materials of the cold storage and the structure of each part of the cold storage should have sufficient frost resistance.Word of mouth recommendation,The refrigeration equipment in the fresh-keeping environment of the quick-frozen warehouse mostly adopts the single-stage compression refrigeration system, with freon as the refrigerant. The evaporation mode in the warehouse is the cooling fan, which can be ceiling type. If the number of warehouses is small and the volume does not exceed cubic meters, the refrigeration mode of the warehouse machine can be considered. If there are a large number of warehouses,Santa BarbaraCold storage board cold storage installation company, the mode of multiple heads in parallel can be considered.Goods are imported and exported frequently and the throughput is large according to the requirements of production and operationThermal insulation rigid polyurethane has low thermal conductivity and good thermal performance. When the density of rigid polyurethane is ~ kg / m the thermal conductivity is only . ~ .w / (m.k), which is the lowest among all thermal insulation materials at present.

The butt joint between the top warehouse plate and the end of the top warehouse plate shall be treated to prevent air leakage and cold running. After all the top warehouse plates are installed, the butt joint shall be filled with foaming material, and the mm wide color steel plate shall be sealed at the butt joint with pull riveting.supply,In order to ensure the safety of construction and cold storage operation, the span between the top storage plate supports (lifting points) shall comply with the following provisions: the polystyrene top storage plate (mm thick) has a very large span of M, and the polyurethane top storage plate (mm thick) has a span of m.Reasonably design the division of fresh-keeping warehouse such as cold storage room, freezer room, machine room, aisle, transportation platform etc; The fresh-keeping storehouse shall be built indoors to avoid excessive temperature and poor refrigeration effect. If it is set outdoors, a sunshade shall be built; Wires shall not be outdoors,Cork board: cork board can be said to be a relatively primitive kind of cold storage. The thermal conductivity of cork board is relatively low, and it is easy to obtain, so it is not difficult to process, so it is generally used as the insulation board in some ordinary cold storage. If you want to pursue better thermal insulation performance, you have to look at the following materials.Santa Barbara,The product shade warehouse is a warehouse location below ℃ and the sun cannot be straight. The humidity is % ~ % relative humidity, and there are corresponding strict requirements for the wall,Santa BarbaraCold storage, ceiling, ventilation disinfection and epidemic prevention of the warehouse. The refrigeration system adopts full-automatic microcomputer electrical technology and does not need to be on duty. It mainly stores western and Chinese grass materials and instruments, and can monitor and record the temperature and humidity in the storage area.There should be excellent drainage pipe standard around the warehouse, the soil temperature should be low, there should be interlayer under the cold storage, and maintain good natural ventilation. Maintaining dryness is very important for the cold storage. In addition, before the construction of the cold storage, the phase electricity of the relative volume shall be built according to the output power of the refrigeration unit. If the cold storage is water-cooled and radiating, there are some unique installation skills when installing the cold storage? The cold storage installed according to these skills is often short in both effect and quality, and the specific installation skills of the cold storage will also make some relatively detailed introduction for you in the following article. When installing the cold storage,Santa BarbaraInstallation of pharmaceutical fresh-keeping cold storage, you should install it from the corner first. Later, according to the height of the cold storage make a hole in the middle of the insulation board, and tighten the angle iron parts until there is a hole on the insulation board