Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.Montreal,　　Whether the pump shaft is bent or rusted. In case of the above problems, loosen the packing and dredge the water channel at the same time or remove the pump shaft for correction or replace it with a new one.　　 bind the exposed copper wire to the cable core evenly,MontrealVertical heavy-duty slurry pump, heat it with an electric iron, and infiltrate tin evenly.Murray Bridge,　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain

　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.　　 the mechanical seal adopts a new type of hard corrosion-resistant tungsten titanate material which can make the pump operate safely and continuously for more than d~ hours.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellerGood quality,　　Commodity.　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall be　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.

　　In order to ensure the demand for water and electricity for production and living, many units, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this, it and the generator naturally become popularEncyclopedic knowledge,MontrealCarbon steel explosion-proof pipeline pump,　　Therefore when the pump temperature is too high,MontrealSubmersible non clogging sewage pump, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.　　Check the three-phase current with an ammeter on the control panel. If the phase power supply is found to be insufficient, the power supply of the submersible pump shall be turned off immediately. Check whether the cable connector, connection point and power switch contact are in poor contact and whether they are the main line. Check whether the circuit wiring is broken or loose, or whether the fuse is damaged or burnt out　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　The utility and durability of the utility model, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.