Friction resistance due to bearing and packing; Friction between impeller and water during rotation; The vortex of water flow in the pump, gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed,Tampa Self priming slurry pump wholesale, so it is impossible for the water pump to completely change the power input by the power machine into effective power, in which the constant active power　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts but also reduce the service life of the parts.Tampa ,　　 Lifting,Tampa Self priming non clogging sewage pump, loading and unloading of electric pump: remove the cable and disconnect the power supply.　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothingMaldives,　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion, which is convenient and flexible.　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.　　If the pump outputs more medium liquid, it will certainly do more work. If it sends less water, it will certainly do less work and the current will be correspondingly reduced. Pump power (kw) = head (m) × Flow (m/s) × The gravity of the fluid (kg/m for water) divided by (power conversion factor) divided by the efficiency of the pump (about

　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating　　 the experimental water shall meet the relevant process requirements.　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump,Tampa HH slurry pump, because its axis is basically vertical when it works but it can be completely immersed in water when it runs, so it is a good choiceQuality recommendation,　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speed　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged

　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, soGood reputation,　　No matter what type of slurry pump you need, Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　 Requirements for the process pretreatment unit for the normal operation of the screw pump the stator of the screw pump is generally made of rubber and the rotor is made of stainless steel. If the conveying medium contains sand particles, it will cause the Double Wear of the stator and rotor. Due to the requirements of the processing technology and materials, the　　How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.Tampa , gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed, in which the constant active power　　 Then reinstall the equipment on the engine and install the rubber hose.　　.