The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation.　　It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.Bayata port,　　 sedimentation tanks, hydropower stations reservoirs, rivers, power plants, open caissons, mines and fish ponds.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellerOtavalo,　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, villa water supply, factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.

　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump,Bayata portZD slurry pump, so we should follow the correct steps to connect.　　Steam will produce air bags, which are harmful to water and seriously damage the vacuum suction. In order to immediately empty the pipe, avoid balloon accumulation. The suction pipe shall be a steep slope rising to the direction of water flow rather than an immediate vertical rise, generally exceeding ., which should be the height of the top water pipe along the pump inlet　　Moreover, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning, and the consequences will be unimaginable.Latest quotation,　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.

　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min,Bayata portSubmersible pump can pump sewage, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.Workshop cost,　　It should be /-/ between. When the packing is worn,Bayata portDeep well pump, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　 Drain the water filled in the motor.　　There is no need to equip auxiliary mixing or spraying equipment, without noise and vibration, and the site is cleaner.Bayata port, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact we use it at ordinary times　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid