With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directlyGambetta ,　　 Motor disassembly: remove the base, thrust bearing, thrust disc, connecting seat of lower guide bearing seat, water deflector, take out the rotor, stator, etc.　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise, so it is easy to burn out the motor.Kutloanong,　　When in use, it can drive the impeller to rotate so as to drive it to flow.　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.

　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　Will the submersible sewage pump get sick?　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pumpagent,Gambetta Booster pipeline pump,　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used, so it is effective when it is used in many mountainous areas　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient,Gambetta Centrifugal slurry pump, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization we will also know that those parts are prone to wear during normal use. In this way, which can offset part of the axial force and prolong the service life of the bearing.Supply chain quality management,　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time and the pump and motor of the equipment used in time are the same shaft, so　　Driven by the pump products represented by stainless steel pipeline pumps, the whole pump industry is constantly moving forward, and with the raw material market driven by this,Gambetta Single stage slurry pump, new stainless steel materials are constantly coming out. The continuous improvement of various technologies and specifications has driven the whole industrial chain to a higher direction.　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.Gambetta ,　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service life　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump