TamborrielVertical multistage centrifugal pipeline pump,

　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possibleTamborriel,　　 when the deep well pump is put into water for use, pay attention to protect the cable. The cable must not be stressed to prevent damage. The lifting weight of the lifting device (such as tripod, hoist or electric hoist) used shall be greater than the weight of the submersible pump, and enough space shall be reserved. A wood that is tied to the wellhead with a rope　　Stop, then tighten the bearing seat, press down the nut, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is looseCimislia,　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.

　　 If the power cord is not well contacted it will also lead to the burning of the motor.　　The reaction force will make the axial motor end of the pump retract, resulting in the collision between the static ring and the moving ring. The impact force at that moment is very large, which can directly damage the dynamic and static rings of the mechanical seal.　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller) magnetic dial indicator, outside micrometer, caliper feeler gauge,TamborrielCirculating hot water pipeline pump, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification clean kerosene, oil basin, cotton yarn, etc.project,　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper,TamborrielCentrifugal slurry pump, feeler gauge, square ruler, copper bar, hammer, V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn, etc.　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump　　Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry', which is wear-resistant and particle passing.

　　When the slurry pump is working, the pump needs to be placed on land, the motor needs to be placed on the water surface during operation and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the waterQuality inspection report,　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, and the site is cleaner.　　 Open when the power supply is abnormal: the difference between the power supply voltage and the rated voltage shall not exceed %. If the voltage is too high or too low, the temperature of the submersible sewage pump will rise. If the power supply is turned on abnormally, the service life will be shortened or the submersible sewage pump will burn.　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.Tamborriel,　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if　　Submersible slurry pumps are mainly used in mining, coal, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump blade