The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, square rectangular pipes, seamless square pipes galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe, which can not remove rust and oxide scale. Therefore, it can only be used as an auxiliary means in production.El palaiso,Elongation after square tube breaking (& sigma;): in the tensile test, the percentage of the length increased by the gauge length of the sample after breaking and the length of the original gauge length is called elongation. In & sigma; Expressed in%.Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.Qorveh,B. low alloy structural steel C. ordinary structural steel and high-quality steel for specific purposes (including high-quality steel)The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.

The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.Polishing process of square tube square tube is widely used in our life, so in the subsequent application process, the requirements for square tube in many places are also quite strict, especially for surface treatment. Today, we briefly introduce how the polishing process should be carried out.Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust, oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.Welcome calls ,For structure: as pile driving pipe and bridge; pipe for wharf, marine pile driving pipe, etc.The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, resulting in ears, folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.

Functional index analysis of qb square tube - angular plasticity refers to the power of plastic deformation (permanent deformation) without destruction of qb square tube data under load.how, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.Brinell hardness,El palaisoGalvanized square pipe, Rockwell hardness and Vickers hardness are commonly used.In recent years, large-diameter seamless square tube plays a good role in economic development. Because there are many types of large-diameter seamless square tubes, square tube is a kind of square tube type. Many materials can form square tube body. Its medium is used for what purpose and where it is used. Most square tubes are steel tubes, which are unpacked, leveled, crimped and welded to form round tubes, Then the round pipe is rolled into a square pipe, and then cut into the required length. Generally,El palaiso65 hot dip galvanized pipe, square tubes per package are mostly in large specifications in terms of spot, and . - ~~ - square tubes are divided into structural square tubes, decorative square tubes building square tubes, mechanical square tubes, etc. according to their uses.El palaiso,The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld,El palaiso70 galvanized square pipe, so it must be densified usually pressurized during the reaction.When storing QB square pipe, we need to select a suitable place. We need to think about many external factors such as the corrosivity of steel pipe, etc. Therefore, the place must be clean, dry and ventilated, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, such as air cylinder or oil cylinder, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.The second is to clean the surface of the opposite pipe. When cleaning the opposite pipe, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, square rectangular pipes, seamless square pipes, galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe, which can not remove rust and oxide scale. Therefore, it can only be used as an auxiliary means in production.