→ wide flange and large lateral stiffness. Strong bending resistance.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.North trudou, As long as the pipe material is high-strength alloy steel, including alloy steel pipes with temperature resistance, pressure resistance, the welding process shall be focused on preventing the tendency of martensite structure and cracks due to welding high-temperature operation. The general process requirements are that the welding rod shall be selected and baked as required and sent to the welder for use. The oil and water shall be removed before welding on both sides of the weld Rust and sundries shall be removed and cleaned. The welding line energy shall be as small as possible to minimize the swing during the welding process. The arrangement of the last weld shall have annealing effect on the heat affected zone as far as possible. Slow cooling after welding, cover with asbestos cloth, etc.Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃);Nelson, this cognition is wrong. H-beam and I-beam are different in shape!The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:

I-beam features: the content of chromium carbon alloy is -%, and the macro hardness is - HRCGalvanized pipe is a name for square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment. Steel pipe has been an essential material in building decoration. Galvanized pipe is also used more in decoration, but hot-dip galvanized steel pipe manufacturers need to know about the size of galvanized pipe and several common sizes of galvanized pipe, which is helpful for your purchase!Alloy pipes can be used for heating (cooling) projects.Job description,North trudouIncoloy825 alloy pipe,I-beam is widely used in buildings or other metal structures. Remove defective pipes within the allowable length.The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.

What is the purpose of flat steelindex,Application characteristics of I-beam: The surface of hot-dip galvanized parts is bright and beautiful.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.North trudou,North trudouQuotation of high pressure alloy pipe,Alloy tube is widely used in our daily life, which provides us with great assistance.Whether I-section steel is ordinary or light because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web,North trudouHow much is the I-beam of 18, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are - that is, the corresponding height is -. At the same height, the light I-beam has narrow flange thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.