Pass designKey technical characteristics of alloy pipe:Administration, Material requirements Hot stamping. Fix the plan product workpiece or preformed vacancy on the rotating journal, with the wheel working pressure vacancy, radial wheel. After one or several solutions, there can also be a variety of methods for the whole process of hollow thick wall rotating body products. Products manufactured by high-precision processing method have excellent physical properties, specification scope mold shell and software requirements,AdministrationHow much is a galvanized pipe of 15,AdministrationHow much is a ton of 25 galvanized pipe, which are very simple, and relatively low product cost. The processing time is not long enough, the processing capacity is not high, the total length of processing pipeline is limited, and the size of machinery and equipment is generally short.Akjoujt,However what we need to do now is to improve the production technology level of China&#;s production process of C-section steel, and step up the formulation of relevant industry standards and inspection standards. C-section steel manufacturers should keep close contact with truck manufacturers and communicate more. In this way, it is more conducive for C-section steel manufacturers to produce C-section steel products suitable for truck industry.Defects of alloy pipe and solutions:Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.

Alloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment, or pipeline, alloy steel pipe stimulates important effects. Stair step plate (stair step plate) is a kind of stair used for platform with steel bar mesh. According to the installation method, it generally has two types: welding fixation and bolt (composition: head and screw). It is directly welded to the keel and does not need the side plate with step plate. It is relatively economical and durable, but it is not easy to disassemble, Thickened side plates are required on both sides of the bolted tread plate, and holes are drilled on the side plates.It is often asked that the shape of I-beam is similar to that of H-beam. What is the difference between them? Many people can&#;t explain it in detail. Here is a detailed answer for you: many people think that I-beam is a domestic name and H-beam is a foreign name. In fact, this cognition is wrong. H-beam and I-beam are different in shape!Workshop cost,Methods of exerting efficiency in application of C-section steelAlloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher, the chemical composition of alloy pipe contains more Cr, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum, aerospace, chemical industry, boiler and other industries because the mechanical properties of alloy tubes change and are easy to adjust.Key technical characteristics of alloy pipe

The wear resistance, fracture toughness impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.Recommendation and consultation,a. In the forming process, the thick steel plate has uniform deformation, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size, specification and model of diameter and wall thickness, especially in the production and manufacturing of steel structure design grade thick wall pipe, especially medium diameter small thick wall pipe, which has incomparable advantages of other processing technologies, and can meet a large number of customer regulations on the specification and model of alloy pipe. Spiral seam high-frequency welded steel pipe (sy- for general low-pressure fluid transportation takes hot-rolled steel strip coil as pipe blank and is often spiral formed at warm temperature. High frequency lap welding method is selected for welding spiral seam high-frequency welded steel pipe for general low-pressure fluid transportation.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam,AdministrationHow much is a 32 welded pipe, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.Administration,I-beam is widely used in buildings or other metal structures. Miscellaneous scabApplication characteristics of I-beam