The surface coating of piano paint is actually the paint used on the surface of solid wood floor for laminate floor. It is only bright paint. The wear resistance of this coating is far from that of aluminum oxide surface. Its wear resistance is low, and solid wood floors are developing towards high wear resistance. Unless you like the coating of this surface.Feature editing voiceNuevaGuinea,The utility model has the advantages of convenient installation and maintenance, solid wood composite floors mostly use adhesives with low formaldehyde emission, and good environmental protection effect.If you want to polish a lot of things, you can minimize the spread of dust in the whole house by closing the door and covering it with plastic cloth, tarpaulin and tape.Hardwood floors often need to be polished during installation.Tan-Tan,If you want to polish a lot of things, you can minimize the spread of dust in the whole house by closing the door and covering it with plastic cloth, tarpaulin and tape.Hardwood floors often need to be polished during installation. There are standard, wide plate and narrow plate in terms of specifications Identify from the package

The cross-section of the floor is rubbed with a file to generate heat in the cross-section, and formaldehyde is fully volatilized (formaldehyde is accelerated at more than degrees, and you can smell the pungent smell at the same time). At this time, you can smell, generally you can smell three different levels of smellThe quality of the solid wood composite board made of high-grade flowers, plants and trees can also be divided into good and bad. Therefore, it is best to select the solid wood composite floor guaranteed by a well-known brand,NuevaGuineaDifference between laminate floor and solid wood composite floor, which can not only ensure the quality but also deal with the problems of the store. Good wear resistance and stabilityExecutive standard,How to lay lacquer cloth?The construction procedures and methods are as follows: first, measure the structural size of the room accurately;Then cut the lacquer cloth according to the size.Note that the cutting width should be slightly larger than the required width to facilitate overlapping matching and trimming during paving.The cut floor paint cloth shall be placed at room temperature of no less than ℃ for about hours, so that the crimped part of the floor paint cloth can be fully extended and ready for the final paving.Special adhesive shall be used for paving the floor paint cloth.Before paving, the nano fiber feels more astringent when it is exposed to water and is less likely to slip. The more it meets water, the more astringent it becomes.It is suitable for families with old people and children. It is the preferred ground material in public places with high public safety requirements such as airports, hospitals, kindergartens, schools, pulled or dragged hard to avoid scratching the surface of the wear-resistant layer.

SPC floor is an economical floor material. Consumers can enjoy the texture of wood grain or stone grain in use without being bothered by noise.According to the requirements of consumers for sound insulation, blocks, plates or coils can be selected.Floor lacquer cloth, also known as floor leather (not PVC plastic floor), is a kind of paving material. It belongs to rubber plastic products. It is one of the indispensable floor materials for the decoration of power distribution room, substation and communication room. The thickness is -mm. Other thicknesses can be made according to the needs of users. The wear-resistant layer is generally less than or equal to .mm.The choice of lacquer cloth products shall be selected according to the suitability of the site.For example, the size of the product is determined according to the space of the house and the size of the place of use.At the same time pay attention to the different places of use, and the selected patterns should also be different.For example, in places that need to be kept clean, you can&#;t choose products with convex effect;In solemn places, it is not suitable to choose products with bright colors and messy.The width of coiled floor paint cloth is mm, intermediate layer and surface wear-resistant layer) is divided into mm and mm;The length of each roll of floor leather is m and m.Other specifications and dimensions can be determined by the supplier and the buyer through negotiation.Because of the requirements of production, each roll of floor paint cloth is divided into several sections (the patterns between each two sections are misplaced), so the length of the small section of a roll of floor paint cloth with sections shall be indicated, and the length of the roll of floor paint cloth shall be increased by at least cm (i.e. not less than two complete patterns).Generally, there can only be one section for high-quality products,NuevaGuineaHow much is laminate floor per square meter, and the number of sections of each volume of first-class products and qualified products shall not exceed ;The length of each section of first-class products shall not be less than m, and the length of each section of qualified products shall not be less than m.When inspecting the appearance quality of floor paint cloth leather, it should be visually inspected obliquely under the scattered sunlight or fluorescent lamp with the illuminance of ( ± LX and LM away from the tested sample.First, observe whether there are cracks, fractures and delaminations on the surface of the floor leather. If so, it can be determined that the floor leather is unqualified.The second step is to observe whether there are wrinkle marks, bubble pollution points and pattern deformation. What cannot be observed are excellent products and first-class products;If it is slight but not obvious, it is deemed as qualified. Go back to the third step to observe whether there are missing patterns on the surface of the floor leather and whether there are defects of the transparent wear-resistant film on the surface. If there is no, it is the first-class product and the first-class product. If there is slight missing or lack of film, it is the qualified product, otherwise it is the unqualified product.Finally, carefully check whether there is deviation during multi-color overprint on the surface, whether there are color differences in different parts, whether the superior products are uneven, and if there are the above two defects, the first-class products are those with but not obvious, and the products with obvious above defects but do not affect the overall beauty are determined as qualified products.Finally, based on the above judgment, the appearance quality of ground lacquer cloth is determined.The plastic coil floor paint cloth shall roll the wear-resistant layer outward on the pipe core and shall be externally packaged.The product name, manufacturer name, product mark, grade, batch number, quality and length shall be marked at the obvious place of each package.In addition to the above three items that can be directly judged by the senses, Anti slip more astringent in case of water, not easy to fallWhen choosing laminate flooring, we should first see whether it is produced by regular manufacturers and whether there is an authoritative certification report;Secondly,NuevaGuineaWhat does floor leather look like, open the moisture-proof layer of the floor, expose the substrate, smell the pungent smell, and the formaldehyde content is likely to exceed the standard.Usually, the methods for measuring formaldehyde emission include perforation extraction method, air dryer method and bellows method.： I can smell faint wood fragrance. This floor shows that the glue content is very low.Up to European standard E level.NuevaGuinea,The standard ones are generally -mm wide, about and long. The wide ones are mostly more than mm long and about mm wide. The narrow ones are - mm long and about mm wide. They are similar to the specifications of solid wood flooring, and most of them are called imitation solid wood flooring.When asked about the service life and wear resistance of SPC floor in the message area of the message board, it is often mentioned to take out artifact such as fruit knife or key and scratch on the surface of SPC floor. If there are scratches, they are classified as non wear resistance.In fact, the national wear resistance test of PVC latch floor is not simply to scratch on the surface with artifact, but to grind and polish the floor with thick bottom circular stone roller under the condition of kg charging. After how many revolutions of rotation and polishing, the wear-resistant layer on the floor surface is damaged and exposed to the speed of rural grass-roots.The rotational speed of this connection point is an index value considering the wear resistance of PVC latch floor.For example, the minimum speed of national composite floor is rpm.Therefore, but I have done some experiments and come to another conclusion