GB No. I-beam is in height, in leg width and in waist thickness.When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Brcko,The second is the control of welding materials to ensure that the welding materials purchased are from formal channels, with quality assurance certificate and certificate, which meet the process requirements; The recovery of welding rod head shall be strictly controlled to ensure the flow direction and dosage; Welding materials shall be baked in strict accordance with the process, and the macro hardness is - HRCHohoe,Key technical characteristics of alloy pipe: Frame line crackDefects of alloy pipe and solutions:

In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum,BrckoCold drawn seamless pipe manufacturer,BrckoHow much is a 4-inch galvanized pipe of 6 meters?, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.The fifth is the welding environment control to ensure that the temperature, humidity and wind speed during welding meet the process requirements.According to the national standard of hot rolled H-section steel in China (GB / t- H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight.A complete range of productsH-section steelI-beam can only be used for beam, while H-beam can be used for load-bearing column of structure. Remove defective pipes within the allowable length.

I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height,BrckoWhat are the manufacturers of high frequency welded pipe, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.Welcome calls , Judged as failing. Application of galvanized pipeAlloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.Brcko, Hot hole breaking cold rolling method. This method is dominated by expansion and expands vertical sliding and skew rolling. The former one is mainly cold rolling by relatively limited mandrel mill, cold rolling by few station mandrel mill, cold rolling by three high limited mandrel mill and cold rolling by fluctuating mandrel mill. In this way, the advantages of high efficiency, low metal material consumption, excellent product quality and excellent automatic control system are more and more widely used. The competitive advantage of the latter one is low cost and short whole process. It is suitable for the processing and manufacturing of CrMoG alloy pipes with large quantities, small types multi specifications and high precision. Therefore, it is widely usedI-beam is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide