Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.After spraying (throwing) derusting, it can not only expand the physical adsorption on the pipe surface, but also enhance the mechanical adhesion between the layer and the pipe surface. Therefore, spray (throwing) derusting is an ideal derusting method for pipelines. Generally speaking, shot blasting (sand) is mainly used for the inner surface treatment of the pipe, and shot blasting (sand) is mainly used for the outer surface treatment of the pipe. Several problems should be paid attention to in derusting by spraying (throwing).Shirakawa, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Square pipe is the name of square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment.Santa Lucia,: it refers to the processing of square tube, which places metal in a closed Jane and applies pressure at the end to extrude the metal from the specified die hole to obtain finished products with the same shape and size. It is mostly used to produce non-ferrous metal materials. Square tube ferrous metal, steel and non-ferrous metal. Before introducing the classification of steel, briefly introduce the basic concepts of ferrous metal, which can save energy.Square tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.

At this time, if the welding wire of the same material is used for spot welding where the thickness is insufficient, it shall be welded to the fixed thickness, ground and sandblasted, and repair welding shall be adopted where there are cracks, even if the steel pipe with another large opening can be made up at one time.Material classification: square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, the reduction is too large, resulting in ears, folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.Process inspection,Superior square tubular steel (both P and s ≤ .%)Generally, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, which can remove oxide scale, rust and old coatings. Professional square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the environment.It is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection, and the density of steel is relatively good. After cold drawing and heating, it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.

Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.Encyclopedic knowledgeStage ( & mdash; )It is learned from the authority that if there is dirt on the outer surface of the square pipe during degreasing, it can be washed with purified water and dried naturally, then soaked with degreasing agent with a dry cloth to remove the oil, and then dried in the open air. When degreasing the inner surface of the opposite pipe, the end of the pipe can be tightly blocked with a wooden plug or closed with other. The degreasing solvent with the volume of % - % of the pipe from the other end shall be sealed with a wooden plug, and the pipe shall be rotated every min. If degreasing is required for stainless steel elbow, degreasing solvent shall be appropriately added to make it fully soaked. After degreasing, pour out the solvent in the pipe, dry the pipe with exhaust fan, or dry it with oil-free compressed air or nitrogen, or dry it with natural air. Large diameter pipes can be manually scrubbed with cotton cloth dipped in solvent; The square tube can also be soaked in a long tank containing solvent for to minutes. The concentrated pipeline and equipment of the concentrated unit can be directly pumped and circulated with % concentrated for pickling after all installation. Pipes that cannot circulate or are not resistant to concentrated corrosion must be degreased separately.Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust, welding slag, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.Shirakawa, mainly in curtain wallHot dip galvanized square pipe is widely used, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?Square tube plays an important role in the rapid economic development. The functions of square tube are different,ShirakawaSmall diameter galvanized square pipe, and its characteristics are also different. Square tube has strict standards. There are many welding processes and advantages of square tube. Let me show you the welding process and advantages of lower tube.Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand,ShirakawaPrice of hot dip galvanized square pipe, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust, oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.