The section of I-beam has good straight pressure and tensile resistance, H steel has its own advantages and disadvantages.I-beam is a long strip steel with groove section, which belongs to carbon structural steel for construction and machinery. It is a section steel with complex section, and its section shape is groove shape. China&#;s imports of I-beams are greater than its exports. The main producing areas are Tangshan Iron and steel, Baotou Iron and steel, Shangang, huangte, Maanshan Iron and steel, Xuanhua Iron and steel, Japan iron and steel, etc.San Carlos,The use of hot dip galvanizing has expanded with the development of industry and agriculture. Therefore, hot-dip galvanized products have been widely used in industry (such as chemical equipment, petroleum processing, marine exploration, metal structure,San CarlosHow much is 50 galvanized pipe, power transportation, shipbuilding, etc.), agriculture (such as sprinkler irrigation, heating room), construction (such as water and gas transportation, wire casing, house, etc.), bridges transportation, etc. because hot-dip galvanized productsDue to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Akouda,C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover, it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibilityI-beam is widely usedAlloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.

Generally, the process of pickling and passivation will be carried out for alloy pipes, but the alloy pipes after pickling and passivation are very easy to rust. Therefore,San Carlos300 seamless pipe 1 meter how many kilograms, five petal quincunx steel pipe, double convex steel pipe, double concave steel pipe, melon seed steel pipe, conical steel pipe, corrugated steel pipe, watch case steel pipe and others.Application characteristics of I-beam:Highly recommended,Pass designUnder the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.

The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.buildAiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Seamless pipe has a high position in steel pipe,San CarlosWholesale of high frequency welded pipe, and there are many large factors. The main usage has accounted for more than %, which is applicable to all walks of life. Seamless pipe factories in China are widely produced. At present, the number of factories in China is also increasing every year, which is determined by the nature and production conditions of seamless pipe. The common production processes and processes are more complex.In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, aluminum, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.San Carlos,Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.What are the uses of I-beam?The section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.