The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump.　　When in use it can drive the impeller to rotate so as to drive it to flow.St. Mikel,St. MikelSubmersible sewage pump,　　 water　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise, so it is easy to burn out the motor.Burewala,　　At the same time, the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence, villa water supply, factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.　　Potential is convenient and flexible. It is easy to operate. It can be operated by a fool who turns on the power supply under immersion; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.

　　Limited. According to relevant materials, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.　　Use a V megohmmeter to measure the insulation resistance between the electric pump motor and the phase to ground, and the value shall not be less than megohm. Otherwise, the stator winding of the motor shall be subject to monotonic treatment, and the monotonic treatment temperature shall not exceed ℃.　　After meters, the sealing of the equipment can not bear the water pressure at this depth.Packaging strategy,　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.　　The application of pumps involves all aspects of work and production, and the types of pumps are also diverse. Some of the same pump have several names, and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck,St. MikelSmall deep well pump, the probability of pump sticking will be much smaller!

　　In addition to the method, materials shall be selected comprehensively according to the nature of corrosive medium, anti cavitation theory, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life, protection should be done well,　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals abrasion　　Starting mode. It can be widely used in industrial and agricultural production, drainage,St. MikelRubber lining submerged slurry pump, fire control, sprinkler pipe network pressurization, HVAC cold and hot water circulation and other occasions.　　Whether the pump is evacuated or overflowed, etc., and handle it at any time.St. Mikel,　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.