With the implementation of China's reform and opening up, the national economy has achieved rapid growth, and a large number of urban houses, public buildings and tourism facilities have been built, which puts forward new requirements for hot water supply and domestic water supply. In particular, people pay more and more attention to the problem of water quality, a common pipe, will gradually withdraw from the historical stage under the influence of relevant countries because of its corrosivity. Plastic pipe,HaidijiaoStainless steel 4K brightness plate, composite pipe and copper pipe have become common pipes in the pipeline system. However, under certain circumstances, stainless steel pipe has more advantages, especially the stainless steel pipe with wall thickness of only . ~ mm. In high-quality drinking water system, hot water system and water supply system that puts safety and sanitation first, it has the characteristics of safety, reliability, sanitation, environmental protection, economy and applicability. It has been proved by engineering practice at home and abroad that it is one of the new, energy-saving and environmental protection pipes with good comprehensive performance of water supply system. It is also a very competitive water supply pipe, which will play an incomparable role in improving water quality and people's living standards.Stainless steel pipe factory stainless steel products are widely used in hardware products, furniture, mechanical structure, mechanical accessories, precision medical instruments, such as furniture, machinery, medical oil natural gas, water, gas, steam and other industries.HaidijiaoSurface treatment difference: surface treatment is usually divided into polishing, wire drawing and wire drawing, and the cost is about yuan and meter. If it is thrown into the lens barrel, the cost per ton will increase by yuan.Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production, nitrogen fertilizer and chemical pipelines.Winkovzi,Stainless steel has been used as a structural material for building new buildings and repairing historic sites for more than years. Early designs were calculated according to basic principles. Today, design codes,HaidijiaoStainless steel pipe 201, such as ANSI as of the American Society of civil engineers, are usedUsing CrO and hsoho as the main components and adding an appropriate amount of mnso.ho coloring solution, the chemical coloring of stainless steel industrial pipe was carried out. The effects of pretreatment process, coloring solution temperature, mass concentration and coloring time on the color film of stainless steel industrial pipe were discussed. Through a large number of experiments, a good formula and process range of coloring solution are obtained. With the increase of temperature and time, the film thickness increases, and the color changes are brown, blue, gold, purplish red and green. After curing and sealing treatment, the colored film of stainless steel industrial pipe has more uniform surface color, good reproducibility, and significantly improved wear resistance and corrosion resistance.Model & mdash; The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.

Add a small amount of sulfur and phosphorus to make it easier to cut.Folding and editing this section of silicon steel strip grain oriented silicon steel strip, also known as cold rolled silicon steel strip for telecommunications industry, is a silicon steel strip with grain oriented structure and thickness less than .mm, which is used to manufacture various power transformers, pulse transformers magnetic amplifiers, converters and other iron cores with working frequency above Hz.Low temperature embrittlement of stainless steel pipe --- in low temperature environment, the deformation energy is small. In low temperature environment, the phenomenon of reduced elongation and area shrinkage is called low temperature embrittlement. It is mostly produced on the body centered cubic structure of ferrite series.technological innovation,The scale pretreatment of stainless steel pipe makes the scale loose, and then acid pickling is carried out for easy removal. The pretreatment can be divided into the following: alkaline salt melting treatment method. The alkaline melt contains % hydroxide and % salt. The proportion of the two in the molten salt shall be strict, low melting point and small viscosity. Only the sodium halo shall be analyzed in the production process, and the content shall not be less than % (wt) It is treated in a salt bath furnace at ~ ℃ for minutes for ferritic stainless steel and minutes for austenitic stainless steel. Similarly, iron oxides and spinels can also be oxidized by salt to become loose ferric oxide, some of the formed oxides peel off and sink to the furnace bottom in the form of sediment. Alkaline salt melting pretreatment Process flow: steam degreasing → preheating ( ~ ℃, time ~ min) ↠ molten salt treatment & rarr; water quenching & rarr; hot water washing. Molten salt treatment is not suitable for assemblies with weld gap or crimping. When the parts are taken out of the molten salt furnace, a stream of alkali and salt mist will be splashed during water quenching, so deep well anti splash water quenching tank shall be used during water quenching. During water quenching,HaidijiaoStainless steel checkered tube, firstly lift the parts basket into the tank, stop above the horizontal plane, close the tank cover, and then lower the parts basket into the water, s stainless steel pipe and L stainless steel pipe are stable, safe reliable and maintenance free. The technical level has reached the domestic level and the international advanced level of similar products until submerged.Household worries.Standard classification - classification: national standard GB industry standard Yb local standard enterprise standard qcb- classification: product standard packaging standard basic standard - standard level (divided into three levels): y level: international advanced level I level: international general level H level: domestic advanced level - national standard: stainless steel bar (level I) gb- stainless welding disc Park (level H)

The back is not protected by argon, and the flux cored wire + TIG process has been applied in China for several years. Flux cored wires such as et-elt-et-elt-t-et-elt- have been produced and applied to field welding, and good economic benefits have been obtained.Workshop cost,The specific steps of continuous casting billet process of stainless steel pipe fittings are as follows: according to different steel grades, the vibration process of mold is matched with protective slag, which can improve the yield of %, save energy and shorten the production cycle, so as to improve the yield of molten steel.Seamless steel pipe): round billet & rarr; Heating → Perforation & rarr; Three roll cross rolling, continuous rolling or → Off pipe & rarr; Sizing (or reducing) → Cooling → Straightening & rarr; Hydrostatic test (or flaw detection) → Mark & rarr; The raw material for warehousing and rolling seamless pipe is round pipe blank. The round pipe blank shall be cut and processed by cutting machine, and the blank with a growth of about m shall be brought to the furnace for heating. The billet is sent to the furnace for heating at a temperature of about degrees Celsius. The fuel is hydrogen or acetylene. The temperature in the furnace is the key problem. After the round tube billet is discharged from the furnace, it should be pierced through the pressure piercer. Generally, the more common piercer is the cone roll piercer. This piercer has high production efficiency and good product quality. It is specialized in stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe with high pressure resistance grade, good waterproof performance, fire and high temperature resistance, corrosion resistance, radiation protection long service life, large perforation diameter expansion, and can wear a variety of steel grades. After perforation, the round tube blank is successively rolled by three roll cross rolling, continuous rolling or rolling. Take off the pipe after sizing. The conical drill bit of the sizing machine rotates into the steel embryo at high speed to form a steel pipe. The inner diameter of the steel pipe is determined by the outer diameter length of the sizing machine bit. After sizing, the steel pipe enters the cooling tower for water spray cooling. After cooling, the steel pipe will be straightened. After straightening, the steel pipe is sent to the metal flaw detector (or hydrostatic test) for internal flaw detection. If there are cracks, bubbles and other problems inside the steel pipe, they will be detected. Steel pipes should be strictly selected manually after quality inspection. After the steel pipe is inspected, the number, specification, production batch number, etc. shall be sprayed with paint. And hoisted into the warehouse by crane.Deformation strengthening of austenitic stainless steel stainless steel has good cold deformation performance. It can be cold drawn into very thin steel wire and cold rolled into very thin steel strip or steel pipe. After a large amount of deformation, the strength of the steel is greatly improved, especially when rolling in the subzero temperature zone. The tensile strength can reach more than MPa. This is because in addition to the cold hardening effect, there are also superimposed Deformation induced M transition.Haidijiao,There are three main reasons for oxidation of stainless steel: production process, which is one of the reasons for oxidation of steel products. In terms of production process and product characteristics, forming a thin oxide film on the product surface is the basic process to avoid oxidation, and it is also one of the main characteristics of steel products different from other steel products. It is specialized in products, renewable resources business and business package Including: stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe. However, when the oxide film is incomplete and discontinuous due to insufficient or negligent production process, resulting in the appearance of oxidation of the product.Stainless steel pipe is safe, reliable, hygienic, environmentally friendly, economical and applicable. The successful development of pipeline and new reliable simple and convenient connection makes it have more irreplaceable advantages of other pipes. It will be used more and more in engineering, and the use will be more and more popular. It has a good prospect.The back side is not protected by argon, the backing welding wire has been developed. Recently, China has also developed the stainless steel backing welding wire (i.e. flux coated welding wire, such as tgftgftgftgf, etc.) It has been applied to the actual construction and achieved good results. We have successfully applied it in the capacity expansion and reconstruction project of Urumqi Petrochemical.