When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started,San FelipeVertical slurry pump, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.San Felipe,　　Is there an important cf fire control cabinet? Analyze the importance of configuring cf fire control cabinet for everyone.　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)Florida,　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　It is also necessary to clean the ventilation duct to avoid blockage.　　 the submersible slag pump is often used to transport pulp containing solid particles so the wear resistance of the pipeline should also be considered.

　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air,San FelipeISG single stage vertical pipeline pump, and also reduce the corrosion and rust as much as possible　　Determine whether repair and replacement is required according to the wear condition of the ring; Check the insulation of the motor stator to see if there is any trace of chamber sweeping damage; Check whether there is sand deposition and sewage blockage at the pump bottom, whether there is sand deposition at the pool bottom, and whether it is necessary to cut off water and clear silt.　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, so as to improve the integrity of the equipment andsupply,　　Most of the time, we don&#;t know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family, when we use it, the flow is small　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.

　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive,San FelipeSubmersible slurry pump, toxic, high pressure and low temperature.Quality management,　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　Ah slurry pump internal structure The pump shaft is bent. After the slurry pump reverses, the reaction force of the impeller may directly top the pump shaft. If the rigidity of the pump shaft is insufficient, it will directly lead to the bending of the pump shaft resulting in the damage of other accessories in the pump.　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the waterSan Felipe,　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is in the traditional slurry pump　　 First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use, multiple pumps need to be used in parallel or standby pumps need to be prepared.　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.