The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.MiamiCheck whether the manufacturer&#;s qualification, business license, organization code certificate, tax registration certificate, production and operation license and other qualification materials are complete. Look at the case, investigate the supplier&#;s performance and the projects served in the past. Whether there is a self built logistics fleet or not, choosing a service provider with a self built logistics fleet can reduce the transportation cost, and more importantly, ensure the timeliness of delivery. After sales service, whether there is a sound and reliable after-sales service guarantee system, and timely solve quality problems in arrival acceptance and subsequent use. Check whether the quality assurance materials such as product quality certificate, material specification and warranty are complete. Check the appearance of the welded pipe, the surface is smooth and flat, the weld is dense, oil stain, corrosion, extrusion deformation and flat cross section. Use a micrometer to check whether the outer diameter and wall thickness of the welded pipe meet the requirements, and the standard wall thickness deviation shall not exceed % - %. NDT shall be carried out for welded pipe with flaw detector. Conduct bending tensile strength test according to the requirements, bend the welded pipe for degrees, and there is no crack at the bend.→ compared with the concrete structure, reduce the self weight of the structure by % - %, and reduce the structural design internal force.La Dorada,The delivery length of I-beam is divided into fixed length and double length,MiamiReinforcement rapid turnover software, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.Alloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher, the chemical composition of alloy pipe contains more Cr, and its performance of high temperature resistance, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum, aerospace, chemical industry, electric power, boiler and other industries because the mechanical properties of alloy tubes change and are easy to adjust.I-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam.

→ the two surfaces of the flange are parallel to each other, making it easy to connect, process and install. Spiral seam submerged arc welded steel pipe (SY- for pressure fluid transportation is a spiral seam steel pipe used for pressure fluid transportation, which takes hot-rolled steel strip coil as pipe blank, often warm spiral forming and welded by double-sided submerged arc welding. The steel pipe has strong pressure bearing capacity and good welding . After various strict scientific inspections and tests, it is safe and reliable to use. The steel pipe has large diameter and high transportation efficiency, and can save the investment in laying pipelines. It is mainly used for transporting oil and natural gas.The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.retailer,After the passivation treatment of alloy pipe, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.I-beam features: the content of chromium carbon alloy is -%, the hardness of chromium carbide alloy is V, and the macro hardness is - HRC

Difference and application description between H-beam and I-beamInstallation materials,Miami6. How many kilograms per meter of sub welded pipe,Miami18 #’s I-beam,When it is used for ground heating and hot spring transportation, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.The third is the welding machine, which must ensure reliable performance and meet the process needs; The welding machine must have qualified ammeter and voltmeter to ensure the correct implementation of welding process. The welding cable shall not be too long, and the welding parameters shall be adjusted when it is too long.I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Miami, cold rolling by few station mandrel mill, cold rolling by three high limited mandrel mill and cold rolling by fluctuating mandrel mill. In this way, the advantages of high efficiency, low metal material consumption excellent product quality and excellent automatic control system are more and more widely used. The competitive advantage of the latter one is low cost and short whole process. It is suitable for the processing and manufacturing of CrMoG alloy pipes with large quantities, small types, multi specifications and high precision. Therefore it is widely usedI-beam features: the content of chromium carbon alloy is -%, the hardness of chromium carbide alloy is V, and the macro hardness is - HRC