Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.Rio de Janeiro,Relatively high stability and high deformation resistance. The mixture is usually composed of hard fine aggregate graded aggregate with high sand equivalent, especially micro seal and polymer modified seal, which greatly increases the strength and integrity of the pavement.Alloy pipes can be used for heating (cooling) projects.Boditi, Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole, etc.Alloy pipes can be used for heating (cooling) projects.When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold,Rio de JaneiroGh3039 alloy pipe, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.

When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project there are many things that must be paid special attention to. Let&#;s take you to know:Filling: welded pipe is welded by electric welding of hot-rolled strip steel, so its influence was not as high as that of seamless steel pipe.Alloy pipe can be divided into round steel pipe and special-shaped steel according to different cross-sectional area. Because the circular area is large on the premise of the same side length, a large amount of liquid can be transported with an annular tube. In addition, when the circular cross section bears the internal or external axial working pressure,What is the stainless steel passivation of alloy pipe?When it is used for ground heating and hot spring transportation most seamless steel pipes are round steel pipes.Inspection basis, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, the chemical raw material transmission pipeline has a wide indoor space.Using alloy pipe to produce ring parts can improve the utilization rate of raw materials, simplify the production and manufacturing process, and save raw materials and production and processing construction time, such as roller bearing ring throwing Nowadays, seamless steel pipe has been widely used to produce hydraulic jack sleeve.

Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %Equipment maintenance,Rio de Janeiro40CrMnMo alloy pipe,After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.According to the data information display information, there is an inseparable correlation between the annual real estate sales data information and the apparent consumption data information of galvanized pipe. From the consumption surface of the middle and lower reaches of galvanized pipe decoration design, elevator car, handicrafts, household appliances and other industries are closely related to the situation of the real estate industry.→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.Rio de Janeiro,I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.I-beam, whether ordinary or light, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.