The excellent performance of copper pipe The copper pipe has the characteristics of and, heating and cooling pipes in all residential commercial housing.After the pipe is cleaned, the welding flux and flux shall be immediately applied to the interface and the bayonet clearance. Sufficient flux shall be thinly coated on the mating surface and assembled immediately, so that dust and dirt will not pollute the capillary gap.Wenji, East Germany,When stacking, reasonable stacking and first in first out shall be achieved.Overview of three production methods of copper tube Copper tube is a very important material for copper materials. There are many ways to complete the production of this copper tube. For copper pipes, the following three methods are generally used to produce materials. The copper tubes produced by these three methods are not only very good in performance, but also very convenient to operate. There are three production methods for copper tube, so what are the three production methods for copper tube?Ayaviri,In the middle and late ten days, although there were good news such as the rise of futures and the increase of production restriction policy in Wu an region, due to the high inventory level, traders had no desire to increase prices, most of them had shipped goods, and spot prices lacked motivation to rise. The market inventory rose significantly. At that time, the market inventory in Handan reached a high level after the festival. The sluggish demand performance for a long time led to the oversupply of the market and the continuous rise of inventory led to the empty market mentality.In the middle and late ten days, although there were good news such as the rise of futures and the increase of production restriction policy in Wu an region, due to the high inventory level, traders had no desire to increase prices, most of them had shipped goods, and spot prices lacked motivation to rise. The market inventory rose significantly. At that time, the market inventory in Handan reached a high level after the festival. The sluggish demand performance for a long time led to the oversupply of the market, and the continuous rise of inventory led to the empty market mentality.The copper tube shall be heated and welded first, and then the joint shall be heated until the heated part turns dark red. At this time, when the filler metal contacts the tube, the filler metal shall melt.

To sum up, due to the influence of factors such as the current spot market price is much higher than the expected winter storage price of merchants, the gradual emergence of supply and demand pressure, and the weakness of raw material support among which the contraction of market demand has a greater impact. Therefore, the author believes that in the short term, the spot building materials do not have the possibility to rise significantly, and the price of building materials may mainly operate in shock, but with the shrinking demand, the supply and demand pressure becomes prominent, However, considering the influence of winter storage and other factors it is still possible for merchants to lower the spot price in November.Advantages: low investment cost, low production cost, high output and low price.In terms of steel billets: at :, some steel billets in Changli were reduced by , and the current carbon square billets were delivered with tax of yuan. After the th National Congress of the Communist of China, the market had doubts about the uncertainty of environmental production restriction and was still waiting for a clearer direction. Therefore, it can be seen that at this stage, and there was no definite pattern of ups and downs. According to the monitoring data of Lange Iron and Steel s cloud business platform, as of the time of publication, B yuan/ton; Jiujiang # - # to Tianjin yuan/ton; The arrival price of Xinji Aosen # is yuan/ton, B steel yuan/ton; Fulen # yuan/ton; Weigang # yuan/ton, B steel yuan/ton.production costs,In Jiangyin market, another distribution center the overall inventory of the current circulation link is about tons, slightly lower than the normal level. At the beginning of this week, the price gap between Jiangyin prices and those in the north has also been able to correspond to the slightly lower circulation inventory. However from the perspective of the policy port of the steel plant, the overall production situation of Nangang,Wenji, East Germany304 stainless steel plate, Hengrun, Dada, etc. is relatively normal, and the amount of resources in the later period remains stable. The overall inventory of Lecong market remains at about to tons, which is a medium normal level, and the recent spot price of Lecong market has a large gap with that of the north.Disadvantages: Due to loose tissue and high pressure resistance, the pipe is only used to produce small air conditioning copper rods.The blowpipe shall be perpendicular to the lead pipe during welding, and the flame shall be moved continuously to prevent local overheating and the flux from carbonizing before filler metal is added.

Advantages: good quality, fine structure, high density, high pressure resistance, large bending deformation, suitable for frequent cold and heat exchange, large temperature difference in working environment,The difference between hard copper tubes and soft copper tubes in use Hard copper tubes can only be used as straight tubes and cannot be bent. Therefore, they are generally used in power plants, switches of electrical equipment, and places where the connection points are far away and do not need to be bent. Compared with soft copper tubes,Wenji, East GermanyStainless steel welded pipe, it can also be used as a hard tube, so the soft copper tube is used in more places, and can be used in a straight tube way, asell as in a coiled tube way. The length of the copper tube can be longer if the coil is used. If the connection point is longer, it can be cut randomly according to the length, so as to prevent leakage when welding the copper tube. Soft copper pipes are used in many refrigerators, air conditioners and other places where bending pipes are needed. When we use copper, we need not consider the preservation problem unless we buy a small amount at home. For example, large manufacturers use copper units to buy a large number of copper pipes once, so there will be a problem. I believe some people do not know how to store unused copper materials, Now let s ask our staff to introduce the storage method of copper for you.Air conditioning copper tube production technology Upward lead method: This production method is electrolytic copper after copper tube is directly melted.After : on October , and sintering machines using semi dry desulphurization continued to be shut down for %. The access of vehicles is alicted. The port collection and distribution vehicles are prohibited from entering and leaving the port area. The city s steel, coking, electric power, cement, chemical and other key vehicle enterprises are not allowed to transport vehicles into and out of the plant. After : on October , the vehicle enterprises in the above industries will implement % of the peak load shifting emission reduction measures. It is estimated that the average daily consumption of sintering powder in Tangshan will be more than yuan, and the purchase of iron ore may still maintain a small amount of prudence. In addition, due to the influence of industrial users & amp; quot; coal to gas& quot;, the recent performance of coke is weak. Therefore in terms of steel plant production, the support of raw materials is weak.Wenji, East Germany,Insert the pipe into the top of the bayonet,e the sleeve on the pipe to evenly apply the flux on the joint, and confirm that the pipe is inserted into the bottom of the socket, then wipe off the excess flux, and the joint is assembled and can be heated.Disadvantages: low output, high production cost and high price. Extrusion copper tube process is a stable and excellent copper tube production method at home and abroad at present. Only the copper tubes produced by this process are more suitable for the field of heating and ventilation, which is the development direction of copper tube industry in the future.The simplest way is to use copper cleaner. Brass, red copper, bronze, etc. can be used. Oil stains, fingerprints, oxide layers, etc. on the surface can be cleaned with copper cleaner first.