Frame line crackThe specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Pete point,Longitudinal welded pipe has the advantages of simple production process, high production efficiency, low cost and rapid development. The strength of spiral welded pipe is generally higher than that of straight welded pipe. It can produce welded pipe with larger pipe diameter with narrow blank and welded pipe with different pipe diameter with blank of the same width. However, compared with the straight seam pipe with the same length, the weld length increases by ~ , and the production speed is low. Welded pipes with large or thick diameter are generally made of steel blank directly, while small welded pipes and thin-walled welded pipes only need to be welded directly through steel strip. Then after simple polishing wire drawing is OK. Welded pipe is welded with strip steel, so it is not as high as seamless pipe in its original position. Welded pipe process: uncoiling of raw materials - leveling - end shearing and welding - looper - forming - Welding - removal of internal and external weld beads - pre correction - induction heat treatment - sizing and straightening - eddy current testing - cutting - hydraulic inspection - Pickling - Inspection (strict control) - Packaging - delivery.I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Prijedor,The wear resistance, fracture toughness,Pete pointDN25 welded pipe more than one meter, impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.c. quality inspection is carried out for alloy pipes, so that the whole process of steel pipe processing is under reasonable inspection and supervision, there are many passivation methods for alloy tubes, the common ones are high temperature passivation or sodium cyanide passivation.

The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels. Divided by weld -- straight welded pipe and spiral welded pipe.After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment,Pete point10# steel seamless pipe, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.agent,Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing siliconizing and so on are commonly used in production. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Plan scheme : for high carbon steel with carbon content of more than .% and high chromium alloy pipe with chromium content of no less than %, the interval is min.

At present, there is still a big gap in the production technology of C-section steel between China and foreign countries.OK or not?,X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, gas, heating steam and other general liquids,Pete point20# seamless pipe factory, X-ray or ultrasonic testing sampling inspection (%) shall be carried out. Fabrication and installation of pipe support:The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.Pete point,The shape of I-beam is similar to that of H-beam. What is the difference between them?The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid, sodium cyanide, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.Defects of alloy pipe and solutions: